Slicing e posizionamento azze Z (6 replies)
Ho visto che quando faccio lo slicing, in fase di stampa ogni volta che cambia coordinate l'asse Z si riposiziona. E' possibile fare in modo che lasse Z si sposti solo in altezza, nello sviluppo...
View ArticleDrucker bricht vorzeitig den Druck ab. (1 reply)
Hallo zusammen. Folgendes Problem: Habe mir den Pearl Drucker geholt. Er hat eigentlich immer gut funktioniert.Druckte schon 19 Stunden am Stück mit ihm. Seit kurzem,bricht er den Druck einfach ab....
View ArticleBed Levelling? Z home point? (3 replies)
Can someone explain to me what the deal with bed levelling is? After a few prints my Z screw pointers are now about 45 degrees either side of the Z bars when Z is homed. 1. Why does this happen? 2....
View ArticleExtrusion problem (1 reply)
Hi all I just recently got my ormerod assembled, and after some struggling with calibrating the beast it printed some parts flawlessly. But now it has started to rebel against me I believe. For some...
View Article7.5 degree steppers with marlin (3 replies)
So I just received my ramps 1.4 board not long ago hooked everything up and I installed marlin on it. I am using pronterface to control it. Right now I am just trying to get movement out of my motors...
View ArticleUpgraded to a E3D hotend and now I'm getting nozzle drag. Can't figure out...
Hey, I have a Makerfarm Prusa i3 8". I just replaced the hot end on the machine from a J-head to an E3D and I'm getting nozzle drag. It's can finish prints but I hear it dragging slightly during...
View ArticleClik here to view.
Shift to left at the same point in the print (no replies)
My first job since building my Prusa i3 has been to print replacement parts for my Prusa i3 as I'm not especially happy with the quality of the ones I purchased but I'm having issues with the X-Axis...
View ArticlePrésentation Prusa Mendel et problèmes (1 reply)
Bonjour à tous, Je suis (ancien !) électrotechnicien et je me suis lancé dans la construction d'une Prusa Mendel V2 kit Emotion Tech (fin 2012) avec Gen7 1.4.1, (Atmega 644 20Mhz) J'avoue que la...
View ArticleConnettore 4 pin molex (3 replies)
Ragazzi conoscete qualche venditore online che vende questo tipo di connettore o qualche metodo per collegare i nema alla ramps?
View ArticleJust wondering....... (no replies)
Has any one tried covering the glass with that window tint stuff the boy racers put on their cars? I don't know what plastic it is, but remember doing it to an old banger I had years ago, and it was...
View ArticleFirst Layer problems (2 replies)
I am encountering a problem with my first layer. I even know how to classify this problem, so maybe you guys can help me. Attached are some pictures of the first layer of one of my prints. Thanks, Nigel
View ArticlePrusa i3 Auto Bed Leveling Servo Twitching? (no replies)
Hey peeps So after falling in love with the auto bed leveling feature shown by the legendary 'Zennmaster' i decided it was a must have for my setup, so i watched all the videos, ordered all the parts...
View ArticleOctoprint - data usage (2 replies)
I'm using OctoPrint to control my Prusa i3 throught a Raspberry Pi and everything is working fine except that it seems to be sending heaps of data over the network. I logged on with my iPhone for...
View ArticleLead content of brass (9 replies)
I've produced several hundreds, maybe close to a thousand brass nozzles in about a year. I love brass as a workable material. But, I think I've probably consumed about a pound of this stuff, just by...
View ArticleYet More Poor Print Quality (1 reply)
So I have been calibrating my printer for a while now trying to get it tuned just right. I have followed Triffid Hunter's Calibration Guide, and the thread on UNI Physics Dept. Both have helped out...
View ArticleM501 To RAMPS And Not Responded (no replies)
Hi guys I am using repetiter-host and printrun sometimes to operate my Mendel i2. Unfortunately, when I wanted to see my parameters from EEPROM using gcode m501, it didn't respond. Neither repetiter...
View ArticleFirmware setting for RS 198-961 (no replies)
Hi, bit of a noob question. I'm setting up my first 3D printer (with Repetier FW) and just wanted to clarify what the best setting is for my thermistor. I have the 100k RS thermistor (198-961), which...
View Article1.75mm through a 3mm hotend (2 replies)
What happens if you feed 1.75mm filament through a 3mm hotend? Can it be done?
View ArticleWhat is "W" Parameter is Pronterface log.? :S (no replies)
When we give Print command in Pronterface, In log it shows the temperature increase for printbed and extruder. What is the "W" in the temperature rise indicate ? I observe when W: ? turns to W:0 print...
View ArticleHelp! ATX PSU for i3 (1 reply)
Hello fellow RepRappers! I've finished my i3 build and I'm very excited to start configuring my rig and make my first print. However, I'm having problems with my power supply. I had a few brand new...
View Article