Réalisation stylo 3D (11 replies)
Bonjour, Je cherche des informations sur la motorisation du filament pour le stylo 3D, il n'y a pas grand chose sur internet, je cherche peut-être pas au bon endroit. Je pense que ce sera le prochain...
View Articlecomment limiter le bruit? (10 replies)
Bonjour, j ai un souci: mon voisin se plaint du bruit quand j imprime. Avez vous des astuces pour limiter le bruit des moteurs?
View ArticleRAMPS Bad? (no replies)
New to the 3D Printing community. Got my printer and assembled it. When I try to home or move I get no movement. I have tuned the pots on the stepper drivers and found out I have one bad driver. I...
View ArticleSpool Holder for a 6" Prusa? (1 reply)
My MakerFarm Prusa is complete and ready to print! I'm seeing the definite need for a spool holder and was thinking it'll be one of my first real prints. Does anyone have a good model for a 6" Prusa...
View ArticlePrusa Ersatzteile (4 replies)
Hey Leute, ich habe mir gerade einen Prusa Drucker gekauft, bei dem aber leider schon einige Teile Sprünge oder ganz gebrochen sind, er ist aller dings noch druck fähig und so hab ich mir gedacht tja...
View ArticleAdjusting stepper drivers (6 replies)
I have had a couple of ruined prints recently due to dropped steps. These occurred on the Y axis this time but have occurred on the Z axis in the past. I adjust the stepper drivers by trial and error...
View ArticleDibond als Druckbett? (3 replies)
Hallo, hat hier jemand Erfahrung mit Dibond Alu Verbundplatten als Druckbett? Wie sieht es mit der Ebenheit und Stabilität von Dibond aus? Ich wollte PLA direkt darauf drucken. Hat das schon mal...
View ArticleResistenza HotEnd (2 replies)
Buongiorno a tutti, sono nuovo del forum. Scrivo per un problema con la mia reprap Prusa i2 appena finita di costruire. Elettronica arduino mega + ramps 1.4. Tutto funziona (motori, fine corsa,...
View Article[SOLVED] Extruder temperature setting problem (no replies)
Hi there, ive just finished building my first printer, the prusa i3. The printers all good to go, for the calibration cube i converted an stl. into gcode using slic3r however as i go to run the file...
View ArticleDual extrusion, E-only move causing XYZ motion, bug in Marlin? (no replies)
I've assembled a Kossel Mini with two extruders (and a dual-e3d end effector) and I'm running Marin 1 from [github.com] downloaded 1/19/2014 with a the modified configuratoin below using RAMPS 1.4....
View Articleprinter not online (4 replies)
For some reason the printer is playing up. (see attached picture) Any suggestions please... I'm going to re-install the Firmware to see if that sorts it for now.. It says it's not online, and yet...
View ArticleMicro Center filament for $19.99 (6 replies)
I am not sure if this is the place to post this but Micro Center has filament for 19.99. I was wondering if anyone has anything to say about it? The brand is "Toner Plastics" which has a MicroCenter...
View ArticleFirmware Upload Gen7 (no replies)
I am trying to upload the Teacup firmware to an atmega644 on which I myself have burned the boatloader file "bootloader-644-20MHz.hex from Gen7 arduino IDE support using winavr/avrdude and a usbasp...
View ArticlePolypropylene sheet sourcing in the USA (1 reply)
Can anyone tell me where I can source the 0.5mm polypropylene sheets in the US? I have looked and looked online and can't find it sold in small quantities.
View ArticleAusdrucke sind spiegelverkehrt (4 replies)
Hallo zusammen, nachdem nun alles an meinem Drucker soweit funktioniert, und ich über "einfache" Probeausdrucke langsam hinausgehe, habe ich bemerkt, dass unsymetrische Teile spiegelverkehrt gedruckt...
View ArticleTaratura Home Asse Z (6 replies)
Ho una Prusa I3, Pronterface, Slic3r, Marlin. Come faccio a settare la posizione iniziale dell'asse Z? Mi spiego meglio: inizialmente ruoto a mano le due madreviti che spostano l'asse Z fino ad...
View ArticleEndStops dont work with Marlin (2 replies)
Hello, I am trying to upgrade my Ramps 1.4 to Marlin. Right now on Sprinter everything works absolutely fine, but when I switch to Marlin the endstops no longer work! Any idea what the problem could...
View ArticleKratzspuren im Druckbild (3 replies)
Hallo, ich habe in den letzten Tagen meinen X400 von GRRF mechanisch optimiert und im Zuge dessen eine 0.3 Düse installiert. Anschließend habe ich begonnen an den Slic3r Einstellungen rumzuspielen, um...
View ArticleClik here to view.
[VDS] Moto-reducteur 5:1 pour extrudeur (no replies)
Bonjour à tous , Suite à une erreur de commande , j' ai 3 moteurs pas à pas avec motoreducteur integré ( rapport 5:1 ). Ils peuvent etre utilisé pour faire des extrudeurs à entrainement direct grace à...
View ArticleHot end thermistor installation problem (1 reply)
Hi all, I am constructing my Ormerod but I cannot fit the glass thermistor into the2mm hole that it suppost to fit into on the hot end. The heatshrink is making it to wide to fit no matter how hard I...
View Article