Gen7 repetier firmware (1 reply)
Hallo Community habe ein Problem beim upload von der Repetier Firmware ich erhalte immer wieder die Meldung: USB device not found obwohl die ganze Hardware auf der Platine sitzt und ich komplett nach...
View ArticleMINEBEA 23LM-C038-P2V o NEMA17? (no replies)
Posso sostituire i motori ,tranne quello estrusore , con 4 MINEBEA 23LM-C038-P2V.? non capendone un h di stepper mi è venuto in mente di cercare un sostituto a questi motori , perchè trovare dei Nema...
View ArticleClik here to view.
(tu)The Titan - A Prusa Modification (no replies)
Hey guys, Initially, we bought 3DStuffMaker's Classic Prusa and did an in depth review and our thoughts. Link: Classic Prusa by 3DStuffMaker Review After constructing it, we wanted to design an...
View Article(tu)Our 3D Scanning Journey (no replies)
Hey guys, We were recently introduced to 3D scanning for an elective at school, we had to explore 3D scanning methods and these are the results. Video Here. We played with structured light scanning,...
View ArticleCiao a tutti! (no replies)
Qualcuno in provincia di Ancona o Macerata ha acquistato una stampante 3D Reprap?
View ArticleNo Movement (5 replies)
I'm having an issue with my printer run off of a rambo board with marlin firmware. I had it printing previously, but came back to the printer after a night and wasn't getting any movement, though I...
View ArticleQualcuno della provincia di Ancona o Macerata ha una stampante Reprap? (no...
Sono di Porto Recanati e cerco qualcuno nella provincia di Ancona o Macerata che abbia una stampante 3D Reprap. Da poco conosco questo tipo di stampante e vorrei saperne sempre di più.
View ArticleAhoj RepRap - Ahoj Slovensko. (no replies)
Ak si sa dostal az sem pravdepodobne vies co je to RepRap. RepRap je open source. Existencia open source projektu stoji a pada na komunite. Toto forum je venovane slovenskej komunite.
View ArticleNeed advice for material to use under hot plate (no replies)
I am building my heated bed. I have a 12X8 1/4 thick Pyrex glass top a 12.25 x 8.25 PCB hot plate (MK1) The problem is that it has a slight bow to it and I need to sandwich it against something to get...
View ArticleClik here to view.
Infill does not fill whole layer (4 replies)
Hi! I have problems with my infill, see the attached picture. In the picture, it already printed 3 layers. You can see the holes in it. What I think is remarkable, the holes are always at the same...
View Article3D Drucker Stottert beim Drucken (2 replies)
Hallo zusammen, Hier ein Paar Daten zum Drucker 1. Mechanik Eigen Aufbau , Druckbereich 400x400x250mm 2. RAMPS 1.4 3. TB6560 mit je einen NEMA 23 in Achse X,Y,Z 4. wildBill's PG35L Direct Drive...
View ArticleDribble in transit (no replies)
A droplet always seems to find its way out and hang on the leading edge of the 'next' target. I've tried lift and retraction in varying amounts with only marginal changes, usually just the location...
View ArticleHotend Santa Fe (4 replies)
Hola gente. Acá hay unas fotos del hotend que estoy haciendo, todavia falta hacer algunas pruebas y retocar algunos detalles pero quiero pensar que esta encaminado. Siendo general la idea es hacer...
View ArticleMurrieta - Need Help (no replies)
All, I am in Murrieta ( just north of Temecula) and I am looking for some help with my Prusa I2... I have it built and have printed a few test cubes but I need some help getting it fine tuned. I am...
View ArticleQuanta energia elettrica consuma una stampante Reprap? (3 replies)
Vorrei sapere se una stampante Reprap consuma tanta energia elettrica. Non è che mi costa di meno andare a comprare l'oggetto in negozio piuttosto che stamparmelo a casa?
View Article2 stepper Y axis vs 1 stepper with driveshaft (no replies)
Im trying to decide if I should design my Y axis using two nema17 (which I already have) or 1 larger stepper to drive both sides. I plan to have linear slide mech on each side of my printer each with...
View ArticlePrint Stopping on Leapfrog Creatr (1 reply)
On my Leapfrog Creatr using Repetier, my prints stop in the middle of G-code, sometimes multiple times depending on the part size. It seems to happen most often at high- acceleration points, but...
View ArticleLooking for parts (no replies)
Hi Im looking for parts to construct a printer for my project. Would like to get prises from sellers in Israel. Best regards Avi
View ArticleHot end : quel choix ? (1 reply)
J'ai acheté une J Head MK4 qui ne donne pas satisfaction : le filament se bloque après 1/2 h de fonctionnement et après de nombreux essais, j'ai décidé de racheter ou de refaire moi-même une hot end....
View ArticleApplied Motion HT17-075 Stepper Wiring Question (2 replies)
I managed to salvage some Applied Motion HT17-075 Stepper Motors at work to use in my RepRap Prusa build I am engaged in. However I am not clear how these wire to my new RAMPS 1.4. See Applied Motion...
View Article