Laser RepRap zu verkaufen (no replies)
Hallo Leute, ich habe vor ca. zwei Jahren damit begonnen einen Laser RepRap zu bauen. Leider konnte ich aus geschäftlichen Gründen das ganze nicht mehr weiterverfolgen. Deswegen möchte ich diesen...
View ArticlePrinting dentures (no replies)
[www.youtube.com] Has anyone thought of refining the precision of the 3D printing to the point when dentures can be printed very chaply? Sounds like a great philanthropic mission. I would set my goal...
View ArticleCura settings for Mendel90 (no replies)
Novice question: I'm trying to slice using Cura on OSX but I can't find the setting where I tell Cura that (0,0) is in the center of the printbed. The result is that all coordinates in the gcode are...
View Articlefried my arduino mega, well two of them in 2 minutes :S (1 reply)
Hi I'm building a delta 3D printer. Electronics are 2 kits from gadgets3d.com bought on ebay.(arduino mega, ramps 1.4, sdramps, G3D drivers.....) Power supply is 12V 30A, switching... I tested tested...
View ArticleAuto Z Stop using all metal hotends (6 replies)
So i was thinking last night that all metal hotends would make it very easy to make a auto Z stop. had a play the weekend using a E3D V4 hotend. Crocodile Clip to the top of the hotend which runs to 1...
View ArticleProblems printing after xcarriage meltdown? (1 reply)
Hello everyone, so my x-carriage melted last week and ive replaced it with a reinforced abs one but im now having trouble printing, before the old one melted i was able to print a 20x20 cube, now when...
View ArticleProblème Makerbot Think-o-Matic MK5 (no replies)
Bonsoir à tous, Résumer des épisodes précédents : - ordinateur cassé parce baby sitter a renversé un liquide sur le clavier - changement de PC et n'arrive plus à faire fonctionner correctement ma...
View Articlerepetier (no replies)
bonsoir à tous, Ma mendel90 me donne entière satisfaction, mais j' ai un dernier détail à régler j' utilise repetier host V0.84 et le firmware 0_71 et j'ai constaté un truc étrange je demande en...
View ArticleNur Z-endstop arbeitet richtig (2 replies)
Guten Abend, ich habe an meinem Drucker 3 Hall-O-Endstops installiert. Und zwar hinten, rechts und oben. Die sind demnach als max endstops angeschlossen. Wenn die endstops nicht ausgelöst sind, lassen...
View ArticleSlovak RepRap forum (no replies)
Hello everybody RepRap is starting to be popular in Slovakia. It would be nice to have a local forum to help the community grow. Thanks Jakub
View Articlequality of 3dprinters-shop prusa i3 (1 reply)
Hi, I'm interested in buying a rep rap but as for many here the budget is quite limited. Now there is this offer from the 3dprinters-shop for a prusa i3 full kit at about 450€. Does anyone here have...
View ArticleHow to I rotate an object in the X plane (1 reply)
I have just started learning Inventor and I have run into a problem. In inventor, and in Meshlab, the object is orientated with the top as I expect it. When I add it to the platter in Slic3r the...
View ArticlePrinter shuts down after adding heat bed (3 replies)
So up until now I was printing without connecting the heat bed since it wasn't working but I found a bad solder connection and after fixing it the heat bed worked and everything heated up right and...
View Article3D tiskarna z cinske elektroniky a hlinikovych profilu - slo by to? (no replies)
Zdravim, chci si taky postavit 3D tiskarnu a mel bych par dotazu. Jsem spis elektronik a programator, takze nektera nazvoslovi asi nebudou uplne spravne (i kdyz me prumyslova robotika zivi) Takze mi...
View Articlestart blob (2 replies)
I finally got my tantillus running. I'm using the tantillus kisslicer profiles with repetier on an azteeg x1 (couldn't get the tantillus marlin fw to compile). When printing starts, the hotend heats...
View Article0.5mm Thin wall printing issue (1 reply)
I build my 1st prusa a couple of month ago but had to rebuilt recently. I'm having an issue that my 0.5mm thin wall is having problems nearer to the top of the print. I've attached a photo showing my...
View Article[Tutorial] 2D Drawing to 3D Model Conversion (no replies)
Hey Everyone, I volunteer at the Innovation Lab at my local city library focusing on 3D Printing, and I get asked by people all the time if and how they can go from their 2D drawing or logo to a 3D...
View ArticleBuild Suggestions. (no replies)
Hello all! I'm new to the RepRap community as I don't have a 3D printer to begin with. I'm quite interested in building my very own RapRap and have been looking into 3D printers for some time now. Put...
View Articledont order from Create3D.com.au (no replies)
not happy jan, first the clunky website caused me to order the wrong filament (my own fault) but the 3Kg spools are only 2Kg!!! what a ripoff,
View Article