Allowing the embedding of an imgur album (2 replies)
Hi, in the past it was possible to insert an imgur album, however, I haven't been here for a month or so and now suddenly all the albums are gone because the codes are not displayed anymore!!! This is...
View ArticleBlown MEGA usb port? (2 replies)
Hi all, I've got a Prusa i3 with a RAMPS 1.4 setup - a kit from reprapdiscount with the smart display. Yesterday I went to use the printer, and did the usual stuff - turned on the ATX power supply,...
View ArticleCalibracion motores (no replies)
Hola mi nombre es Sebastian, soy de argentina y recurro a alguno de ustedes a ver si les paso el siguiente problema: Con la impresora ya armada me dispuse a calibrar los motores, los de 200mA todos...
View ArticleBroken micro USB socket (4 replies)
Hi guys, Have had an Ormerod for a couple of weeks now and have managed to print a fair few parts (albeit with some weird behaviors at times). During an overnight print my usb interface has detached...
View ArticleWir brennen einen Bootloader neu in das Mega2560 (no replies)
Hallo, jedem ist es vielleicht schon mal passiert, der Arduino meldet nur noch Timeout weil beim Uploaden schief ging oder der falsche Bootloader vom Chinesen verwendet wurde. Alles kein Problem: 1....
View ArticleHow to configurate a PTC100 tempsensor in Marlin (no replies)
Hello I'm trying to configurate the frimware Marlin so it can read the temperature from a ptc100. I have the ardurino mega and a ramps 1.4. As there is no pre configuratet temperaturetable in marlin...
View ArticleRepetierhost problem (no replies)
TAk mam problem s tim, že když do repetierhost importuju stl a je zaškrtlý mesh tak se nezobrazí a většinou celej program crashne
View ArticleK 8200 Bauhöhe Z Achse (2 replies)
Hallo, nach dem ich seit 4 Wochen einen K8200 betreibe, habe ich viel in diesem Forum gelernt. Danke an alle, die hier so fleisig Posten!!!!! Auch mir erging es so wie vielen anderen mit den Macken...
View ArticleOrmerod commisioning problem (4 replies)
Hi I have followed instructions and got to the point where i was changing the settings in the config.g file for the axis compensation. I changed the config.g file and copied on to the SD card , now I...
View ArticlePrusa i3 direct drive new build (3 replies)
Hello all. I have been building a Prusa i3 with Wades extruder over the past few months. I will try to post some pictures later, as I am at work. The following will describe some of the configuration....
View ArticleExtruder and Heatbed No Readings (no replies)
Hey Everyone, I could use some help. I have a Mendelmax 1.0 that I purchased and have been using for about a year and a half. Board is Ramps 1.3a. Great printer. Printer was working great. Now all of...
View ArticleResistance issues (1 reply)
I'm just about ready to wire up my machine but I came across some issues whilst checking the resistance. The thermistor in the hot end is giving me ~140Kohm while the thermistor in the bed is giving...
View Articleplasty Prusa i3 (1 reply)
Ahoj, vytiskne mi někdo komplet plasty na Prusu i3 s hlinikovym ramem? Prosim o nabidku s cenou, děkuji.
View ArticleHeat Settings (2 replies)
What do the bed and the hot end heat settings need to be, I tried to print my first test piece and all i got was a load of curly stuff stuck to the head !! How annoying is it that you can't pause or...
View ArticleRubicon 3D - Kickstarter (no replies)
Hallo gerade im Netz gefunden... [www.kickstarter.com] Was denkt ihr? Gruß Ronny
View ArticleRidges on Top Layer Infill (1 reply)
I have noticed that on prints with more complicated geometry the infill on the top layer of the prints have ridges from where the infill starts and stops. On prints without a complicated top layer the...
View ArticleSlicer Profile im Netzwerk nutzen (3 replies)
Hallo zusammen, ich nuze Repetier host und den dort eingebundenen Slic3r. Ich würde nun gerne die Profile bzw. das Verzeichnis, wo die gespeichert sind, auf meinen Server legen, damit ich mit desktop...
View ArticleChinese Stepper Drivers Burned Arduino (no replies)
Dear all I'm in the process of understanding all the electonics behind my Ultimaker, but this one goes beyond my current (still somewhat basic) knowledge. Please help... I was about to install a...
View ArticleHot end thermistor (no replies)
I've had a problem installing the hotend thermistor. I found the PTFE heatshrink when shrunk was still too large to allow the thermistor to slide into the heater block. I have had to carefully cut the...
View Article