Avanzamento pet (7 replies)
Ciao ragazzi, da un po' sto costruendo una stampante 3D volevo sapere se sono obbligato a installare l'avanzamento del pet sul asse Z gravandolo di ulteriore peso, tengo a precisare che la stampante...
View ArticleSoft PLA and Laybrick (no replies)
We have a small amount of soft PLA and the new Laybrick now in stock. Available in both 1.75 and 3mm. Laybrick print example [www.facebook.com] Soft PLA info and example...
View ArticleTrying to build my first Reprap (3 replies)
Ok so I started my Mendal several years ago when I was in college and am just now trying to finish it. I have it all built but can't get the controls to talk to the computer. I am using Pronterface as...
View ArticleNew Smart LCD Controller displaying blank squares (no replies)
Greetings. I just received and installed a new Smart LCD Controller, re-compiled and flashed, and all I'm seeing is a blank display (with solid squares if I turn up the contrast.) I've attached and...
View ArticlePrusa se bloque au debut de l'impression (1 reply)
Bonjour, Je recherche un peu d'aide. J'ai viens de finir de monter une Prusa. Firmware repetier 0.83 avec LCD smartcontroller. Arduino 2560 et RAMPS 1.4. J'utilise le logiciel repetierHost pour...
View ArticleIs this Seller any Good? (3 replies)
Hey Guys, After a bit of searching, I came across Gadget3D. (http://gadgets3d.com/index.php?route=product/product&product_id=87) and was wondering if there safe/reliable? Thanks, Jo1212
View ArticleSmall IDs (1 reply)
I cannot print any tube-like object (washer or tube) where the inside diameter is not too small. I've calibrated my TAZ for X, Y and E steps. I've tried to run this calibration routine...
View ArticleClik here to view.
Stepper Motor Wiring (no replies)
Good evening I bought the Ramps Ultimate package from reprapdiscount. now I want to wire my stepper motor to the Ramps board. I followed the guide here: Guide My connectors should look like this...
View ArticleGen7 1.5. ATX power supply (1 reply)
I have been running my 1.5 board for quite a while with power just going through the disk connectors. I just bought a new ATX power supply and plugged it in, switched the jumper to ATX. When I turn it...
View ArticleZ Axis MATH &"E" Axis ? (2 replies)
Hi, I'm using Repetier as my host application & am so close to finally calibrating my Prusa i3... but for some reason the Z-axis is not stepping far enough each turn .. So I think I need to...
View ArticleIssues with Arduino and multiple printers (1 reply)
I have two printers both using Arduino Mega 2560 boards, one has a board about a year older than the other. When i try and connect to the newer board my laptop doesnt recognize it. If i install the...
View ArticleGenerating thermistor table. (5 replies)
Trying to get thermistor table up for PT100 Thermistor. here is what iv got to work with : [helgem.com.tw] Trying to use this [github.com] But cant figure out most of the variables (beta r1 r2) Steven
View ArticleInformation [Backers] (1 reply)
I would presume to ask those who know... Im looking to build a RoStock/Kossel. Previously allot of the internet video makes mention of backers who... well almost like a single man kickstarter...
View ArticleClik here to view.
I found a new plastic filament material (4 replies)
ABS with electricity conductive power. It has more usage. 3D printing a PCB board become ture.
View Articletwitching stepper motors (no replies)
so i was dry printing with my prusa mendel i3 today (sanguino 1.3a) and my y axis stepper motor got hot so i turned the entire printer off when it cooled down and i powered on again all the stepper...
View ArticleNEW 3D Printing Shop opens in The Rocks, Sydney (no replies)
The 3D Printing Studio at Shop 5, 80 George Street, The Rocks, Sydney 2000 is the 1st 3D Printing shop in Australia. If you are looking for training, printing, printers or material please come down...
View ArticleBarrel, Can it be drilled for airflow (4 replies)
Hey guys, Just wondering if any of you Drill venting holes in the side of the barrel or your hotend setup? I was thinking this may help cool the top section better to prevent pla from expanding
View ArticleHow to repair broken potis on g3d a4988 drivers (no replies)
Hi, I broke two stepper drivers in one week (http://gadgets3d.com/index.php?route=product/product&product_id=72). I was really gentle on turning the potis with my ceramic screwdriver. Are they...
View ArticleAbnahme a satte 14 Prozent abercrombie and fitch schweiz (no replies)
Am allerwenigsten abercrobie kann ist in der Regel bestellt viele davon diese Websites und die Erh?hung der Unterstützung der Volumen der Auftr?ge der Artikel senkt die Kosten für der Aufwand für ein...
View Articlepulley läuft unrund (5 replies)
hallo an alle, habe mir hier im forum einen gebrauchten mendelmax gekauft, nichtsahnend, keine erfahrung, voller vertrauen in die ehrlichkeit der menschen.... , einen drucker der angeblich "wirklich...
View Article