"PID Autotune failed! Temperature to high" (2 replies)
Hi all. I recently replaced the hot end resistor on my RepRapPro Huxley with a new cartridge heater and nozzle. Afterwords I noticed that, in Pronterface, the hot end temperature tends to oscillate...
View ArticleWhere are Slic3r profiles saved ? (2 replies)
Where are Slic3r profiles saved ? If I use Pronterface and do a Settings -> Slicing Settings it appears to pick up my profiles from ~/.Slic3r and it knows my nozzle and filament size But if I then...
View ArticleVerkaufe (Tuning) Prusa (fertig aufgebaut) (no replies)
Hallo, ich verkaufe einen meiner Prusa 3D Drucker. Mir fehlt die Zeit und er staubt nur ein. Dabei ist: - Wade Extruder - 0.5mm Düse (GRRF) - MK1 Heizbett mit SSR! - Meanwell SP320-15 @ 18 Volt -...
View ArticleStällmotorer bara "skakar" (no replies)
Hej! Gett mig in på detta byggande, satt ihop en Prusa mendel i2, köpte plast ifrån en på blocket. Elektroniken är Ramps 1.4 mm ifrån Gadgets 3d Nema 17 motorerna är stadiga ifrån tyskland 2,5 amp....
View ArticleExtruder Calibration (4 replies)
Hello, Now the biggest complaint I have on the printing quality is that there are quite a few blobs and hairlines, most of which are produced when the extrusion stops and restarts (when it prints some...
View Article[RRW] GT2 Timing belt (1m) and GT2 Pulley €3.99, Cable chain €4.99 (no replies)
We now also have GT2 timing belt and pulley available! [reprapworld.com] Also for wiring you extruder a cool cable chain is for sale: [reprapworld.com]
View Article[Worldwide, NL based] Printed-Parts for any model available PLA/ABS (no replies)
I will print you the Printed Parts for any model you would like. These are printed on an Ultimaker, with PLA or ABS. Just what you like. You can order the printed parts for a MendelMax or a Prusa (i3)...
View Article[Worldwide, NL based] Printed-Parts for any model available PLA or ABS (no...
I will print you the Printed Parts for any model you would like. These are printed on an Ultimaker, with PLA or ABS. Just what you like. You can order the printed parts for a MendelMax or a Prusa (i3)...
View ArticleFloor/Table/Bed Level (1 reply)
So I am preparing to start calibration on my reprappro Mendel. I have had a lot of fun building it. I want to build an acrylic case around it, and I also need a table/workstation to set the 3D printer...
View ArticleYou have failed me for the last time opsen sorce communtiy!!! (3 replies)
OK, not really you, my beloved horde of hackers :). But there is something of value that I'm trying to salvage in the whole Makerbot-going-closed-source fiasco. Not just the Makerboters, but the...
View ArticleA couple of problems with printed object (no replies)
I've printed something which I have designed (with SCAD) for the first time today. It's a shame that it was not anything useful - it has no practical use, other than the fact that my 5 year old son...
View ArticleRepetier Host - Idee ? (2 replies)
Hallo, ich hätte eine Idee für den Repetier Host: Es wäre klasse, wenn man eine festlegbare Anzahl Buttons (zb. auf einem eigenen Reiter "Sonderfunktionen") zur Verfügung hätte, deren Beschriftung man...
View Articlehorizontal shells (2 replies)
Horizontal Shells seems to have no effect at all. I was noticing the problem with my prints and decided to take a look at the g-code in Repetier. When you look at each layer you will notice that the...
View ArticleGaufen Dame Nike Free 3.0 V2 Smaragdgrøn/Hvid Online Shop (no replies)
Geschweißte Overlays Richtung Ihrer Basis zusammen mit niedrigeren zellulärer Ebene zusammen mit Interieur Nähten.nike free run. Neben diesen spezifischen Frauen Nike Shox Unze. Von Schuhen kann...
View ArticleTutoriel OpenSCAD (1 reply)
J'ai fait un tutoriel sur OpenSCAD (j'appelle ça un tutoriel mais ne sais pas ce que c'est, un « tutoriel »…) Bon, ce machin fait 10 pages : http://reprapide.fr/tutoriel-openscad-introduction. Bonne...
View ArticleSuche: 3x Zahnriemenräder T5 (no replies)
Hi, Ich suche drei Riemenräder für T5 Zahnriemen mit einer Riemenbreite von 10mm für eine 5mm Welle mit Verschraubung. Zähnezahl von 12-14 Zähnen. Material: ABS, Aluminium oder ein anderes Material,...
View ArticleWird 2014 das Jahr des 3D-Laserdrucks? (no replies)
QuoteDer 3D-Druck könnte im kommenden Jahr deutlichen Aufwind bekommen, weil dann wichtige Patente rund um das Lasersintern auslaufen. Bei dieser Technik wird per Laser Pulver schichtweise erhitzt, so...
View ArticleEndstoppullups: are they defined? If so, as what? (3 replies)
Hi, So, my endstops are working fine, but I have a Q that has been bugging me, so I thought I'd ask: In my Confinguration.h file (I use Marlin) there is the followingcode : // corse Endstop Settings...
View ArticleVon einem Mega zum ersten Drucker (13 replies)
Hallo reprapler, ich habe beschlossen einen 3D Drucker zu bauen. Ich denke die folgenden Fragen provozieren die, was ich eigentlich drucken möchte. Das kann ich euch aber auch nicht sagen und da der...
View Article[Canada/USA] Reprap Prusa i2 Kit ......$499.99 (no replies)
Up for sale is a complete kit for the Reprap Prusa i2..... Price $499.99 + shipping(CAN&USA ~$60.) All plastic parts printed on a dimsension 3d printer for strength and accuracy, 100% solid fill...
View Article