PID Werte richtig einstellen? (6 replies)
Moin, Ich habe das Problem das der Extruder schlecht die Temperatur erreicht bzw. hält. Wenn ich zB 245 Grad einstelle dann geht es recht schnell auf 240 ( 1-2 min ) , und dann dauert es ewig und die...
View ArticleProblem with settings (2 replies)
The android prints fine if I load the gcode file. However if I load the .stl file the object centers in the top right corner I seem to have the settings for pronterface and slic3r as stated in the pdf...
View ArticleY motor slows at some point (no replies)
Hi Y motor runs normally then slows at some point during print at Y home direction then goes at normal speed when prints in opposite direction. I marked with red at second cube image pattern where Y...
View ArticleClik here to view.
Como imprimir estas Piezas? (1 reply)
buenas!!! La consulta es como imprimir estas piezas ya que tienen partes en que la maquina deberia imprimir en el aire... Algun consejo o metodo para imprimirlas??? gracias saludos
View ArticleRepetier Host .90b "Pauses" (1 reply)
Guys - I'm running Repetier Host on three different computers, driving three different printers, all running Repetier firmware. Since the upgrade, each printer / computer combination has experienced...
View ArticleFilament feed through barrel and nozzle (1 reply)
Hi All, I'm another new reprapper, joining the fray with lots of questions and very little experience. So please excuse my improper use of terminology (and feel free to correct). I've just gotten...
View ArticleWhat type of technology does the zprinters from 3D systems use? (no replies)
Is it SLS? I know it's powder based. Is there any open source projects? The quality is just so much better than fuse filament printers and no support structures are needed.
View ArticleMix G1 extruder filament problems (1 reply)
Hello all, I am having an issue with my Mix G1 printer where the filament is backing up and flowing out the bottom of the PTFE rod. I can't leave the printer alone for too long because this...
View Articlejhead stop heating (3 replies)
Hi, my printer was working fine, then when i starting printing again, the bed is heating up but not the extruder (stay at 25). I checked the wires, everything seems to be ok, i even took another...
View Articleextruder / material problem?? (5 replies)
Ahoj, muzete mi nekdo prosim rict, co vse muze zpusobovat chybu pri posunovani plastu do hotendu??? mam s tim ted trosku problem na 0,5 trysce. plast mam 3mm prumer a pohybuje se kolem 2,9 az 3,09 (...
View ArticleRep host 0.90b does not work with prinrboard/Marlin firmware (no replies)
Description and repetier.90B logfiles are here: [forums.reprap.org] Reposting because no reaction in old thread... Hanspeter
View Articlechi puo stamparmi questi pezzi? (1 reply)
ciao a tutti cerco qualcuno che sia disposto a stamparmi questi pezzi senza magari,se possibile,chiedermi un esagerazione....e magari consigliarmi anche un buon estrusore.... allego i file.... grazie...
View ArticleX and Y endstops not working (1 reply)
Hi everyone, I am having an issue with my mechanical endstops in the x and y axis. I have connected them from COM and NC to - and sig on the sanguinololu. And when connected to pronterface they do no...
View ArticleCooling fan placement. (3 replies)
The extruder tip is only slightly below the part to which the cooling fan is attached. Thus that part can hit the front left bulldog clip under some circumstances. Is that because I did something dumb...
View ArticleRecherche de Firmware adapté (no replies)
Bonjour Je viens de réaliser une FOLDARAP complète , avec une carte RAMPS 1.4 et un Firmware SPRINTER .Résultat les axes marchent bien . La montée en température de la buse 0.3 mm est bonne , mais je...
View ArticleSimplicity rules! (no replies)
My lesson learnt today was that the problems are usually simple rather than obscure complexities. For those with a sense of humor .. I used to work in tech support. A client called up and said that...
View ArticlePrusa I3 Prusa Nozzle + Gregs Wade ? (1 reply)
Good evening guys, I want to built an Prusa i3 Printer equiped with a prusa Nozzle, I want to use this Extruder : Gregs Wade Extruder Now there are 3 Stl versions of it: The: * groovemount * jhead...
View ArticleClik here to view.
Intricate print with support (2 replies)
I found this [www.smopic.com] model on the web of a beautiful warrior princess and really wanted to print it. After a few hours of modifying, combining and smoothing I was ready. I first printed her...
View ArticleRequire a lot more heat for the same print...need some help (2 replies)
Last night I printed an object and it printed fine. Today I started printing the object and it started out fine but by half way my filament was starting to sputter (not sure what the official name...
View ArticleUS Rep Rap i2 electronics and hardware (no replies)
Complete RepRap i2 kit $600 (excluding plastics) +$50 for plastics PM me with inquiries
View Article