A4988 Correct Vref to use? (2 replies)
Can someone just confirm for me what i should be settings my A4988 Black Edt Driver to in regards of Vref. Iv always just set at 0.4V and not really had issues. But since experimenting with all metal...
View ArticleGen 7 Connection Problem (1 reply)
Hi, I just finished soldering the gen 7 v1.5 and uploaded repetier firmware but it doesnt seem to work... when i try to connecti in the repetier host, the electronics keep repeating "?start" in the...
View ArticleGuter Preis? (1 reply)
Ich bräuchte einmal eure Hilfe, meint ihr ich sollte die hier bestellen oder kennt ihr eine bessere Seite? Mit freundlichen Grüßen Florian
View ArticleSTM32F103RBT6 mini board ( ebay) (1 reply)
Hello all, Is the STM32F103RBT6 mini board with tft somthing cool to use for the printer, I order one, to see how its work, i have not a lot programming skils. Did sombody tray this board ones, or...
View ArticleHeizplattengröße (1 reply)
Hallo zusammen, ich schreibe gerade an einer längerwierigen Ausarbeitung zum 3D-Druck! Dafür bräuchte ich eine Antwort bezüglich der Heizplatte, die man ja zum Warmhalten des gedruckten ABS-Bauteils...
View ArticleQualcuno se ne intende si scanner a luve strutturata? (1 reply)
Qualcuno se ne intende di scanner a luce strutturata? E' possibile farne uno "fai da te" spendendo poco?
View ArticleProblems w/ thermistor & TeaCup (no replies)
Hi Teacuppers, Since my last mail, I have upgraded to a Teacup-capable Arduino, and successfully used it with the manual control panel in ReplicatorG. It moves in all three directions and heats, but I...
View Articlehelp retraction (no replies)
Ciao a tutti, sulla mia Prusa I3, utilizzo l'estrusore che trovate in questa pagina link estrusore, siccome mi dava dei problemi di vibrazioni, l'ho messo esterno, quindi ho fatto un bowden, come hot...
View ArticleREPETIER à sec... (2 replies)
Bonjour Sans faire de pub , dans le mensuel de juin de Electronique Magazine, un important article informatif sur les imprimantes 3d, a augmenté mes pauvres connaissances. Ce qui a attiré mon...
View ArticleClik here to view.
Kleur van de maand: Juli (no replies)
De kleur van de maand voor de maand juli is blauw. Dus ABS 1.75mm , ABS 3.0mm , PLA 1.75mm en PLA 3.0mm zijn deze maand 22,50 per kilo!
View ArticleHello! First advise needed. (2 replies)
Hello! Well, my story will sound same as your all stories were in the past. I am totally new to this whole thing. Where should I start off? What 3d program is must suitable? Ive been familiar with 3ds...
View Articleerreur de compilation Arduino IDE et Sanguinololu v1.3a (1 reply)
bonjour à tous. je suis nouveau dans le monde RepRap. je viens de me procurer un kit Mendel v2 et une carte Sanguinololu v1.3a w/ATmega644p. la personne qui me l'a vendu n'a jamais réussi à s'en...
View Articlegoogle reader (no replies)
hey anyone out there have a good alternative to the google reader Reprap Repstrap Aggregate feed.? i forgot that its going going gone here PDQ. so i need to find a replacement for it.
View ArticleStepper drivers - failure modes (1 reply)
Sorry if this isn't the right place (I'm fairly new). I've heard that there are 'issues' with the stepper drivers letting out their magic smoke if they are disconnected when powered. Does anyone here...
View ArticleStepper Voltage Rating (1 reply)
My RAMPS, steppers, and Pololu's were sold in one package as a kit. Should I be worried that the steppers I was sent are rated at 2.8V? It looks to me like the RAMPS schematic is saying they will be...
View ArticleVariant of Goopyplastic's Tantillus Variant (no replies)
Hi Folks I've been working on a variant to Goopyplastic's excellent T-Slot Tantillus and I'd like to get some feedback before I start building it in earnest. I’m uncertain if this should be a new post...
View ArticleGen 7 annoyance >:D< (1 reply)
I am trying to make a printable version of the Gen7 board 1.4. The problem is that it is opened on gEDA. I have neither the skill nor the patience for this. When I try to delete the silkscreen layer...
View ArticleClik here to view.
Mendel90 keeps disconnecting (no replies)
Hello, I keep on getting the same problem with my Mendel90. The printer disconnects almost everytime I use it. It was not a problem until now, because I just had to reconnect, but yesterday the...
View ArticleRamps power question (no replies)
Just started wiring up my motors to the ramps board and was wondering if there is a proper powering on sequence? USB power to arduino then external power supply or other way around? Or does it not...
View Articlethermistor and heater mounting in the block (no replies)
hi, i am assembling my new buddaschnozzle, i was wondering how to put the thermistor in the heating block, should ig lue it or something to keep it in place? should i put it all in the middlle of the...
View Article