Clik here to view.
Hohe Druck Auflösung nur mit SLA ? (2 replies)
Es heist ja immer das man hohe Auflösung nur im SLA Druck herstellen kann und nicht im FDM. Daher hab ich mal kleines gedruckt Wenn ich auf der Messe sehe was Profifirmen mit ihren FDM Druckern...
View ArticleY axis drift (1 reply)
I'm having problems with the Y axis, and it comes and goes. This image shows one good and one bad. The bad one is off more than 2mm in a 10mm Z height. At the top, the bed is shifted to the plus Y...
View Article3D printer for bitcoins? (1 reply)
It looks like two emerging technologies are beginning to merge. What do you guys think about purchasing a 3D printer for Bitcoins? [www.bitmit.net]
View ArticleAre there "plugs" for the Ramps power socket? (no replies)
Hi, Most ramps boards seem to come with this: http://www.molex.com/molex/products/datasheet.jsp?part=active/0395321004_TERMINAL_BLOCKS.xml#partdetail as the standard power connector, which receives a...
View ArticleBranchements sur carte Funduino (no replies)
Bonjour a tous Je suis en train de terminer le montage de mon imprimante, et je voudrais avoir la validation des branchements éléctriques de ma carte funduino (légérement différence des arduino...
View ArticleRepetier Firmware for Sanguinololu (no replies)
Hey, After doing some research i think i have found out why my 3D printer isn't working properly, I think it is due to having the wrong firmware. The Sanguinololu board (with ATMEGA1284P#) has Marlin...
View ArticleIntermittent EndStops (no replies)
Hi All, I am trying to connect up my endstops to my sanguinololu 1.3 and they seem to be intermittent at best when using pronterface. I have tried checking the status and seen the output and they...
View Article[TO] Problema ad estruder ABS nero... (no replies)
Ciao a tutti... mi presento, sono uno smanettone torinese e ormai da qualche tempo sto stampando soddisfacentemente con le mie prusa (riviste e ottimizzate nel tempo) e J-head mk 4/5. Non ho problemi...
View Articleheute rtl 2 (no replies)
hi, heute abend 19:00 uhr rtl 2 welt der wunder gibts einen bericht über3d drucker. wird bestimmt interessant ;) gruß stanza
View ArticleSanguinololu 1.3a 1284p - no power at heatbed. (no replies)
Hi. Im new in 3d printing and im trying to finish my mendel Prusa with Sanguinololu 1.3a and i have a problem. There is no power at heatbed. I measured power on hot-end - there is normal 12V. When i...
View ArticleApparent slicing issue when bridging with infill of zero (no replies)
I stumbled into what seems like an error while doing the bridge torture test with Slic3r 0.9.10b. With three perimeters, and infill set to .25, the bridging goes from the infill on one side to the...
View ArticleMijn Prusa i3 (4 replies)
Op verzoek, foto's van mijn Prusa i3 build. Nog End stops monteren en dan vooral veel kabels netjes wegwerken.
View ArticleRepetier FW Advance_L extruder spinnt. (2 replies)
Ich bin grad dabei meinen Drucker weiter zu Optimieren und wollte mich mich mit dem Advance algorithm beschäftigen, leider jedesmal wenn ich bei Advance_L einen wert ungleich 0 eintrage läuft der...
View ArticleAchat de pièces pour une Prusa i3 (1 reply)
Bonjour, je souhaite fabriquer une prusa mendel i3 et comme ce sera ma première imprimante 3D, j'ai quelques questions. Je vais commencer par détailler les pièces que je compte acheter j'ai vu ce kit...
View ArticleLernfähiger Anfänger braucht euere Hilfe (1 reply)
Hi Leute, nach viel hin und her, will ich es wagen mir ein 3D Drucker zusammen zubauen. Als Objekt hab ich mir den vorläufig ausgesucht... [reprap-fab.org] Leider brauch ich noch die Hilfe für die...
View ArticleHuxley Heatbed no GND connection. (no replies)
So ive finally set up my Huxley all ready to go. But the heatbed doesnt seem to work...Ive checked all the connections and found all of them to be fine, the thermistor has a resistance of around 93 K...
View ArticleMissing material on last layer (no replies)
Hi, I noticed that our Prusa Mendel (v2) stops printing prematurely on the last top layer. The last few milimeters are left out and this leaves some ugly holes in the printed model. What can be the...
View ArticleRepetier-Host - Fill einstellung für kleine Objekte (10 replies)
Hallo zusammen, bin ja auch noch recht neu hier und muß mal die alten Hasen was fragen. Ich nutze Repetier-Host V0.90 + Slic3r und da hätte ich bezüglich der Fill funktion eine frage. Wenn man einen...
View ArticleTop layer sinking in (1 reply)
Hi, We are printing with PLA and noticed that on small prints that the top tends to become messy and "sinks inward". Are these the effects of no cooling? Here is an excample: [nicolinux.org] I'd...
View ArticlePronterface stuck on "Sending" (1 reply)
I just build my Huxley all works well accept the Heatbed and Extruder. I test the extruder by sending M302 to allow cold extrusion, however it does not return any thing back it just reads "M302...
View Article