Shorted Out Stepper Drivers (2 replies)
So I just shorted out the GND of one stepper driver against the +12 of another stepper driver. It arced and the Arduino smoked leaving the TX and RX lights stuck on. So I know I'll have to get another...
View ArticleProbleme Steuerung Ramps 1.3 erste Inbetriebnahme/Verkabelung (1 reply)
Hallo Allerseits! Ich habe mir vor über einem Jahr einen Fabbster zugelegt. Leider ist es mir durch meine Arbeit nicht möglich den Drucker aufgrund seiner Größe zu transportieren oder aufggrund der...
View ArticleAxes only move in small increments (1 reply)
Dear Reprap Gurus, I'm working on my i3 build and have come across this strange problem. In Pronterface or Repetier host I can move the axes up and down by 0.1 without any difficulty, but when I try a...
View ArticleLaptop doesnt recognize Generation 7, v1.5 (no replies)
A very good day, first off all: happy new year! Finally i found some time to work on my 3d-Printer and after all the soldering work was down i tried to connect the printer to my laptop. (as seen here:...
View ArticleAV350 Crash (no replies)
I have crashed a s tarrett AV350 vision system in the Z Axis, the machine will not move, is there a way to move the Z Manually, any help will be good
View ArticleMegatronics v.2.0 ventola???? (no replies)
Ciao a tutti, come da titolo, qualcuno sa come modificare il firmware Repetier per abilitare l'accensione delle 2 ventole sulla Megatronics v.2.0? Mi pare che utilizzi i pin 6 e 7, ma non so dove...
View ArticleStepper driver only works if i touch it?! (1 reply)
Hi all, I've fine tuned the currents on the trim pots and still have this peculiar problem. The x-axis only moves when I touch the A4988 driver around the processing chip. Originally I thought this...
View ArticleVendere le stampanti di propia produzione... (no replies)
è una domanda che mi faccio oramai da un pò. Se io mi progetto una RepRap, la costruisco e poi voglio venderla...come privato potrei venderla su eBay senza tanti problemi (ovviamente specificando che...
View ArticleGutes Reinigungsmittel für PLA Haftung auf Glas gefunden (no replies)
Hallo! Ich möchte kurz meine Erfahrungen bezüglich der Haftung von PLA auf Glas (Borsilikat) schildern und meine Lösung vorstellen. Ich hatte sehr schlechte Ergebnisse mit Aceton, Isopropanol,...
View Articlemicrosteping na ramps 1.4 (no replies)
Ahoj ,mám ramps 1.4 z reprap.me a nemá jumpery na nastavení krokování (nechci defaultni 1/16) ,zkusil jsem obvod mechanicky rozpojit ale krokovaní zůstalo pořád stejný,muže prosím někdo poradit?
View ArticleX-Axis Squealing! (2 replies)
Hello all, new to the forum, but have one of the limited edition RS red ormerod's. Its been printing fine, but yesterday, it seems to have developed an intense and irritating squealing. doesn't seem...
View ArticleMendel 90-Neuling -kleine Probleme (2 replies)
Hallo! Im Dezember habe ich mir einen Mendel 90 gekauft. Nachdem das Paket sehr schnell aus England ankam ging es auch gleich ans Aufbauen. Der erste Druck verlief Problemlos (dieses Android-Männchen)...
View Articletaratura motori (1 reply)
salve, dopo aver risolto il problema degli endstop grazie a mic adesso non riesco a tarare i motori, mi spiego ho provato con il calcolatore prusa ma i valori che mi da no vanno bene, allora ho fatto...
View ArticleEthernet connection problems: possible solution (5 replies)
I've been looking at the unreliable Ethernet connection. The main problem I found is that after a network error occurs, it doesn't attempt any sort of recovery. As a result, it won't accept a new...
View ArticleNeues Forum (no replies)
Hallo, macht doch bitte ein neues Forum für Neue die noch nicht so richtig Ahnung haben vom dem ganzen. nennt es von mir aus "Neueinsteiger-Forum" oder irgendwie so. Und macht oben drüber einen Thread...
View Articlereprap prusa mendel y axis problem (no replies)
Nevermind I like a idiot forgot to adjust the endstop
View ArticleDiscussion/Proposal: Reprap Community Standards (1 reply)
For a while now, I thought that it would be nice to have as a community, a set of standards or specifications that would allow the commutability of parts between machines of different designs, etc....
View ArticleVersion 95D (no replies)
The 95D version does not show support after slicing I have checked box to add support but does not show after slicing. The earlier version showed support material but was too excessive and wasted a...
View Articlerichiesta Kit Plastiche I3 (no replies)
Salve ho bisogno di qualcuno in zona che mi stampi delle Plastiche per la I3 in zona di bari da spendere massimo 40€
View Article