DIR pin (no replies)
Got a simple doubt on DIR pin. X_DIR_PIN will be high for one direction and be low for opposite direction right? My DIR pin is always high and hence my stepper is rotating in only one direction. Any...
View ArticleAmperaje (no replies)
como aumentar el amperaje que sale de la ramps hacia la resistencia? Gracias.
View ArticlePrinted objects too thick (no replies)
Hi all, I'm using an Eventorbot, which is technically a repstrap I guess. I'm having issues getting parts to print to the correct dimensions. My Z axis is calibrated spot on and I can hold the dial...
View ArticleHow about air bearings made of plastic? (1 reply)
Still working on my first own printer I'm wondering, if it shouldn't be possible to print bearings working with compressed air. While the surface quality of the inner side of the bearing is less...
View ArticleCompatible PLA spool for Makerbot Replicator 2 (2 replies)
Hi, Suppose this is a bit of knowledge to share with you people, I have a Makerbot Replicator 2 and run out of filament last week, I went direct to Makerbot to get some pla and lead time was 2 weeks...
View ArticleStepping Inconsistencies [Sanguinololu] [Prusa] (3 replies)
I am having trouble getting my machine to step. I believe there are multiple issues happening, and am concerned that some of my components may be damaged. I am using a Prusa Mendel with sanguinololu...
View ArticleAlimentation ramps 1.4 et lit chauffant (1 reply)
Salut tout le monde ! Je crois que j'ai trop trainé dans les differents tuto et sites de ventes, et du coup je me suis completement emmelé dans ce qui concerne l'alimentation d'une reprap: J'ai une...
View ArticleRepetier Firmware und Host....Druck startet nicht (no replies)
Hi Habe auf das Mega2560 Board die Repetier Firmware 0.83 und im Host die 90. Version installiert. Wenn ich auf verbinden gehe, kann ich alle Motoren fahren. Heizen des Extruders und des Heizbett's...
View ArticleExtruder Stripping Filament (1 reply)
Hi, I'm currently trying to calibrate my extruder - but it doesn't seem to be grasping the filament correctly. As I understand it, I'm using a wades geared extruder & a J Head nozzle print head....
View ArticleGrundeinstellungen für Bowden Extruder (1 reply)
Moin Moin Ich konnte vor kurzen bei Stoffel einen V3 Bowden Extruder ergattern und benötige etwas Hilfe bzw. Erfahrung bezüglich der Grundeinstellungen. Mein Extruder ist natürlich von den Schritten...
View ArticleClik here to view.
Solid Top issue (no replies)
Hi all. I am relatively new to reprap and slic3r. So I apologize for my limited knowledge. If you look at the image here, you will see the one on the right has a solid top portion (this was printed...
View ArticleArduino 2 (no replies)
Ciao a tutti, Volevo sapere se fosse possibile utilizzare arduino 2 al posto dell arduino mega? Naturalmente senza stravolgere il firmware. Grazie in anticipo. Danio bonello
View ArticleDelta Ceramic 3D Printer (need help) (no replies)
Hi! I would like to build a printer like this one: [www.youtube.com] The parts I already own are Gecko drive - G540 4-Axis Digital Step Drive: [www.geckodrive.com] ( it is controled via the parallel...
View Article[RRW] Megatronics Summer sale! (no replies)
Temporary offer: get 4 Pololu DRV8825 (md2a) stepper drivers instead of Stepsticks * with your Megatronics Basic kit. Only €104.99, so you save €12! [reprapworld.com] * Limited offer, while stock lasts
View Articlewarning about "deep recursion on subroutine..." (no replies)
Hi, I am new to Slic3r. I have used Slic3r 0.9.10b to slice an object at 100% scale and get the following warning. But I slice the same object at 50% scale is successful. Deep recursion on subroutine...
View ArticlePresnejší homing pre rostock () pronterface (2 replies)
Zdravím :) Snažím sa kalibrovať znova svoj rostock (menil som pár mechanických častí) a všimol som si že pri väčšej rýchlosti mechanické endstopy niesú až tak presné ako by som chcel no na druhej...
View Articleexplicacion de las constantes en configuration.h (1 reply)
Hola! Como habrán visto, tengo varios topics escritos que en todos los casos conducen a temas de calibración de la máquina. Ahora bien, me gustaría entender conceptualmente cada uno de las constantes...
View ArticleSettings di stampa, confrontiamoci! (no replies)
Vorrei aprire questo topic per raccogliere le vostre configurazioni per stampare, così magari i meno esperti (come me) si fanno un'idea sulle impostazioni da cui partire.. Ad esempio io questo oggetto...
View Articleforum settings bug in time zone (1 reply)
Having seen that the software was upgraded recently, I thought I'd better report this one. It is not possible to set time zone as GMT with daylight saving enabled, if I do so, it sets the zone to...
View ArticleRamps 1.4 + DRV8825 - default micro stepping (no replies)
Hello, I'm building a Rostock and using Ramps 1.4 + DRV8825 Drivers. The default micro stepping in this board is 1/16 . DRV8825 support 1/32 micro stepping. When I configed my rostock to 80 steps per...
View Article