First Print Issues on Prusa i3 (4 replies)
Hi! I just printed my first calibration piece and attached is the result I got. I am using PLA plastic my hot end temp is set to 192 C and the bed at 60 C. I am using 3mm filament and extruding at...
View ArticlePC ABS mix? anyone make it (no replies)
I have seen stratasys use polycarbonate ABS mixed material. anyone making it in 3mm filaments?
View ArticleClik here to view.
3 Kanal Type K Thermoelemet Sensor bis 999 Grad (no replies)
Hier mal vorab wieder mal was neues, wird Open Source, bin gerade an den letzten Tests Ist im Moment für die Rumba Elektronik Ein 3 Kanal Type K Thermoelement Sensor bis 999 Grad was MArlin Anzeigen...
View ArticleAuckland 3D Printing Meetup (no replies)
Hi Folks, I've started up a meetup group for Auckland 3D Printer enthusiasts. You can find out more here Auckland 3D Printing Meetup I am taking suggestions for our first meetup venue and timing so if...
View ArticleClik here to view.
Is it worthy for the filament (1 reply)
I just find a ABS filament from EBAY.But is it worthful? [cgi.ebay.com]
View Article3D printer Prusa Mendel metric-prusa not responding to pronterface. (1 reply)
Hmmm, same error happening again. Tried slicing a new .stl file to load updated gcode file into pronterface and same error. Unplugged power and USB and same error. Pronterface seems to behave ok until...
View ArticleExturder gear not turning[INFO] (1 reply)
For all noobs, youre trying to print and your extruder gear is just sitting there sputtering! For the Melzi controller go and set the current at 1 volt, then loosen up your feed tension screws and...
View ArticlePLA not sticking (no replies)
For noobs! When you print look at the trace it makes if its thick at first and thins out you need to increase your feed rate, you can enter M503 to see settings and the feed will be shown at the top...
View ArticleReprappro mendel owner (2 replies)
Hi any reprappro mendel owner here? I got mine few weeks ago and hope to find more guys with the same printer. thanks mike
View ArticleBuse bouchée (8 replies)
Bonjour, Il y a t-il moyen de déboucher un buse de 0.4mm. Avec l'extrudeur chauffé au max, ca ne débouche pas.... Un gros merci^pour votre aide cameleon
View ArticleDying PLA/ABS/Nylon (4 replies)
Hi all, I've recently been looking into colouring my prints - I saw this blog where the guy dyed his nylon filament before putting it through the printer (Nylon Dye) but I was wondering if this is...
View ArticleHow Can I Remove the Aluminum Scraps From Cut Profiles? (1 reply)
We have alüminium extrusion plant that we cut the produced industrial aluminum profile according to the order of customer. While we are cutting profiles the al scraps occur and enter into profiles and...
View ArticleHOT END E PIATTO NON RISCALDANO (9 replies)
Taratura sella mia prusa i3 quasi completata, ma la temperatura sia dell'hotend (Budaschnozzle 2.0 w/ 0.5mm nozzle ) sia del piatto ( mk2 ) rimane a 27 gradi circa con delle leggerissime oscillazioni....
View ArticleDelta Robot (non è un cartone animato) (no replies)
Salve a tutti, mi sono iscritto da poco, e sono estremamente interessato da queste piccole meraviglie. Vi volevo chiedere se questo lo avete visto? Che ne pensate? l'unica cosa che mi lascia...
View ArticleProblems with M.O.B 3d Printer (no replies)
Nice to meet you all, I have M.O.B 3d printer-Romsrcaj and I'm encountering some problems This is my steps after before operating the printer 1. i install the ftpi driver...
View Article100$ 3d printer (6 replies)
it was posted several weeks ago within the Polar bots section ... but today I have read a zdnet article about it: [www.zdnet.com] and a youtube movie here: [www.youtube.com] regards, mihai
View ArticleRamps LCD Smart controller Temperature uncontrollable raise! (1 reply)
Hi, I have set up my LCD Smart Controller. It is connected, it reads temperature. It does the x,y,z homing. But I have some problems: 1) when I set the PLA preheating it does not stop at 180 Celsius....
View ArticleProdej filamentů ABS v CR (no replies)
Zde je odkaz na prodej ABS filamentů a kaptonových pásek. Pražský obchod - pouze internetový, ale osobní vyzvednutí je možné. 3dfab.cz
View Article[UK][worldwide] belt and pulley kits £15!!! (no replies)
Hi We are now selling high quality belt and pulley kits for standard printers for £15: http://www.3distributed.com/ for rostock printers for £25: http://www.3distributed.com/
View Article