Has anyone used Rainbot 3D for filament? (2 replies)
On the 11th of this month, I ordered 3 spools of filament from Rainbot 3D. It is now 10PM on the 14th and I have yet to be able to find out if my order has shipped or not. I have sent two emails with...
View ArticleAlimentazione Scheda (1 reply)
Buongiorno ieri sera ho avuto questo problema: La mia scheda 1.4 non va più in modo autonomo solo con alimentazione 220 ma va solo se collego usb...che parte della scheda ho bruciato? Scheda 1.4...
View Articleyou can know more (no replies)
Kobe 8 Galaxy For Sale Shoes are so hot sale in our store. We can see the shoes not only designed special, but also wear comfort. If you find the Cheap Lebron 10 Dunk Man For Sale shoes, you can not...
View Articleprobleme mit der z achse nach dem slice mit slir3 (1 reply)
hi, habe da ein problem. wenn ich slic3r bebutze dann bewegt sich die z achse beim drucken nicht also sie fährt nicht hoch so wie sie sollte. bei skeinforge hat es immer geklappt. und beim verbinden...
View ArticleNew to Reprap and broken extruder (no replies)
Hey All, I am new to 3D printing and have just finished my first build on a Prusa i3 but during the build I stuffed up and cracked the hinged part on my Greg's Hinged Extruder. Wondering if anyone...
View Articleprinting 90 degree edges - how to improve quality? (jerk, acceleration,...
Hi, My prints are really great, but when it comes to a e.g. 90 degree turn the quality of my prints are really worse (please see attached pictures) Is there anything I can improve in my firmware or at...
View ArticleEinfache Anleitung mit den ersten Schritten für die Elektronik (4 replies)
Hallo Leute, ich bin relativ neu hier in der 3D - Drucker - Welt. Gelesen habe ich schon so einiges, bin jedoch nicht so ganz hinter die Elektronik - Software - Geschichte gestiegen. bei...
View ArticleSimpson 3-Arm Drucker (2 replies)
"It's cool man" -> [www.thingiverse.com] und -> [www.adafruit.com] und hier -> [forums.reprap.org]
View Articlesolid bottom/top layers: infill every layer vs. every n layers (no replies)
Hi, When slicing with e.g. fill every 2nd layer I do not get an infill at EVERY bottom or top layer - was this changed from somewhere 0.9.8 to 0.9.9 ? Even if I enter 3 bottom layers I still do get 2...
View ArticlePROBLEMA ASSE Z (no replies)
PRUSA I3. DOPO AVER VISTO L'HOME DELL'ASSE Z , DA REPETIER HOST FACCIO SALIRE DI ALCUNI PASSI L'ASSE Z , A QUESTO PUNTO SE PREMO HOME SI BLOCCANO I MOTORI E VIENE FUORI UN RUMORE DI BLOCCO E LO STESSO...
View ArticleMelzi Board Failures (1 reply)
Has anyone else had any problems with Melzi boards failing? I just replaced my second board in around a year. Both times the failures resulted in inaccurate temperature readings and hot end...
View Article3d portraits for the blind (no replies)
I am working on piecing together a 3d printer, prusa i3, as some of you already may know. I will not be able to actually start building it until August/September... One of my motivations in building...
View Article3D printer filaments. (no replies)
Hi Guys, I was wondering if anyone has used any filaments from RepRap-Walmart before. They seem to be quite good in terms of service and answering my questions and stuff. But I am not sure about the...
View ArticleMataerial "Anti-Gravity" Printing (2 replies)
I recently saw the video below, and this is the first time I've seen a 3D printer of this type: [www.mataerial.com] [www.youtube.com] Is there a particular name/category for this kind of 3D printing?...
View ArticleBrenda Steinberg Bakersfield (3 replies)
i want to be a part of reprap i am Brenda Steinberg Bakersfield. best regards, Brenda Steinberg Bakersfield
View ArticleQuestion sur Endstop axe Z (1 reply)
Bonjour à tous et merci de m' accueillir au sein de ce forum tres sympa et surtout trés instructif. Je viens de finir de monter une prusa I3 , et apres pas mal de galere pour configurer mon firmware...
View ArticleObjekte Positionieren (1 reply)
Hallo Ich habe mitlwerweile hinbekommen einzelne Teile zu drucken *freu* wenn ich nun mehrere teile Platzieren möchte befinden sich Teile des Drucks außerhalb des Druckbereiches ??? Muss man da noch...
View Articlevon Repetier 0.81 über 0.82.2 nach 0.83 - Probleme (1 reply)
Z.Z. arbeite ich ohne Probleme mit Repetier 0.81. Weil ich den Spruch "Never change a running system" kenne möchte ich auf 0.83 updaten. Ich habe daher die "configuration.h" und "pins.h" von der 0.81...
View ArticleRepetier-host extruder and print bed temperature problem (1 reply)
Good day All I am having a problem with the temperature that Repetier host ver 0.85b reports from the print head and the print bed. Both are reported at a starting temp of 200 C. with or without the...
View Article