V: Zahnriemenräder, 20 Zähne, Aluminium: 2€ (no replies)
Hi zusammen. Ich kann ein Kontingent Zahnriemenräder veräußern: 20 Zähne, 5mm Bohrung, Aluminium: 2€ [www.manupool.de] Der passende Zahnriemen, GT2: 3.50€ der Meter [www.manupool.de]
View ArticleAt a loss (3 replies)
So my printer has been running very well lately on all prints. I have my e calibration perfectly, I double checked it with 30 and 50mm of extrusion and measured it perfectly. I have double checked my...
View ArticleRepetier Host homing question (2 replies)
Hi all, Home button work after startup printer . X home , Y home or Z home works everytime . When pushing home after startup then doing something on printer (shift extruder by hand, fixing someting...
View ArticleAnyone try 24V+ on the 11A line and 12V+ on the 5A? (1 reply)
Question in the title. Anyone try a 24V Source for the heater? and keeping a 12V Source for the rest of the electronics?
View ArticleCHE LACCA USATE? e vale anche per i pelati ;-) (no replies)
Da buon "pelato" mi son sempre chiesto se mai avrei utilizzato "lacca" in vita mia....... caso voglia che si..... A parte gli scherzi tracciamo un bilancio delle marche che utilizziamo e che risultati...
View Article4" bolt too short for extruder? (no replies)
The 4" 5/16 bolt I got for the extruder seems short. Did I print the wrong extruder body or gear? [attachment 14962 4_inch_extruder_bolt]
View ArticleRAMPS 1.4 and End Stops (Marlin) (no replies)
I am trying to run Marlin with Ramps 1.4 and three end stops (mechanical) and can't seem to get it configured correctly. End stops are wired to C (COM) and NC. In Pronterface sending M119 gives me...
View ArticleDifférence diam extrudeur et fil (no replies)
Bonjour à tous. Je viens vers vous car je souhaite acquerir un prusa mendel v2. Par contre dans le kit on me propose ces choix: For 1.75mm Filament with 0.3mm Nozzle For 3.0mm Filament with 0.5mm...
View ArticleHas anyone tried herringbone Wade's gear on Mendel90? (no replies)
Just wondering if anyone had done this, and whether the reduced backlash made a real difference in print quality? Also, if so, is there an STL file I could download?
View Articlel'irc france fonctionne t il ou rencontre t il des probs de connections (no...
bonjour a tous je rencontre des prob pour me connecter a l'irc france (un chat bien utile ) depuis lundi 13 mai 2013 14h. depuis plus moyen de me connecter suis je le seul ?:S
View ArticleGoing nutty (7 replies)
Hi all, Have had my printer for 9 months or so now I suppose. Was going OK but now I can't print anything - have lost my printing mojo. Some prints look good and then crumble apart (too cold?). Some...
View ArticleHoming Retraction Not Working (1 reply)
I have an older UP! printer that had no electronics (I got it that way from Craigslist) and I've been restoring it with the RAMPS 1.4 board. It has been going well an I've made a few prints and so far...
View ArticlePrinted Parts for High School Design Course (no replies)
Hey folks, I am a high school manufacturing teacher looking to build a prussa mendel I2 with a design tech class I am teaching in the fall. I am looking to source the printables for this project. If...
View ArticleThermistor Table (1 reply)
Hi Ich habe da ein kleines Problem. Meine Temperaturanzeige für den Extruder ist absoluter Bogus. Ich kann zwar halbwegs drucken aber in seltenen Fällen dreht der Extruder zwar, aber extrudiert nicht....
View ArticleMotor don't move .help me (17 replies)
I have the RAMPS electronic 2560 v2 (no SD card) . I download firmware Spinter. Do this firmware need SD card? How do I have to resolve it ? Thank you.
View ArticleFIrst prusa i2 build (no replies)
Just got my shipment of plastic parts in, hardware and rods are otw and should b here by the end of the week. Any tips besides the reprap.org prusa i2 assembly instructions? I am going to use fender...
View ArticleExtruder not extruding (5 replies)
Hi, I built my first reprap pro Huxley. (First Reprap ever for me.) Everything went great. (Took longer than I thought it would) Except that when I went to run my first part everything ran except the...
View Articleheater,thermistor not work (3 replies)
Repetier, hi, I am using Lambo board, honeywell thermistor. I had built my 3d printer 1 month ago, but i can't operate it until now. I have uploaded Repetier firmware, but x,y,z axis work correctly...
View ArticleQuick help with Openscad (3 replies)
Can someone give me a quick rundown on how to use the modules that come with openscad? Im particularly interested in hardware and nuts_and_bolts. I tried looking at the manual but it kinda confuses me...
View Article3D printer from electronics waste (no replies)
If you didn't already see it on the RepRap blog, there is an interesting article about a project called W.AFATE, which is an effort to build a 3D printer from recycled electronics at the WoeLab in...
View Article