Bridge, questione slic3r 0.9 vs 1.0rc (2 replies)
Ciao, ieri sera mi sono imbattuto in una serie di bridge da 45mm che non riesco più a stampare. Pla 185° / jhead 0.35. / vetro con lacca / duct con ventola attiva Dopo vari tentativi andati a vuoto...
View Articleprogrammation découpage laser (5 replies)
Bonjour , Voila je cherche un programme permettant de faire du découpage laser en 2D Auriez vous des pistes à me donner svp ?
View ArticleY Homing (7 replies)
I was wondering why the plate doesn't run to y motor upon Y Homing. The macro for Y Homing contains the line: G1 Y220 F2000 S1 Just checked this command in Pronterface and it is being ignored! If I...
View ArticleProblem printing from SD card (no replies)
Hi, I encountered a problem with my SD card printing. I used to be able to print from SD card but recently I have been encountering some problem even mounting and unmounting my SD card. I am using...
View ArticleSanguinololu con LCD Controller (3 replies)
Hola a todos: Alguno por casualidad tiene funcionando una Sanguinololu con algun cotrolador SD/LCD. Con que firmware?
View ArticleNophead Extruder connection PCB (no replies)
Hello to all! Can some one tell me, where can I buy Nopehad extruder PCB connection. I have search on Web, but I can't find enything! Please Help!
View ArticleHow to Send G-code to RAMPS 1.4 (1 reply)
Hi guys I am using repetiter-host and printrun sometimes to operate my Mendel i2. Unfortunately, when I wanted to see my parameters from EEPROM using gcode m501, it didn't respond. Neither repetiter...
View Articlelights on mendel90 (1 reply)
i want to attach some lights on the frame of my mendel90, i was thinking this lights [hobbyking.com] but how can i power them by using to melzi or do i need to use a battery?
View ArticleQUESTION LOGICIEL CREATION et GCODE (no replies)
Bonjour, a tous, je poste ici un nouveau sujet pour ne pas tout melanger... Voila j'ai assemblé un mini traceur pour faire mes tests de comprehensions du systeme REPRAP.... Mais voila, je rencontre...
View ArticleJak tisknout Bridges (no replies)
Ahoj, nastavuji tiskarnu a mel bych dotaz ohledne nastaveni tisku Bridge ve Slic3r. Foukat nefoukat na to, jak rychle je delat a zda snizit Bridge flow ratio. Nebo neco jineho ? Jak jste toto...
View ArticleProblem with drivers (4 replies)
I am using a windows vista machine and when I connect up the duet board to the machine it comes up with a message "USB device not recognised. One of the USB devices attached to your computer has...
View ArticleRFQ - Delrin Bearing Covers (no replies)
Hello, I need Delrin covers for 688 bearings manufactured. They will need to be a tight fit onto the bearing and have a 10mm radius crown on the outside, tolerances are fairly loose on all but 2...
View ArticleProblem mit RAMPS 1.4 und Smart Controller LCD (2 replies)
Hallo zusammen, ich habe mir bei Amazon den Sainssmart Smart Controller LCD 2004 gekauft. Habe ihn an mein RAMPS Board angeschlossen, die Parameter geändert und hochgeladen. Das Display funktioniert...
View ArticleRumba und 1/32 Schritte pfeifen? (4 replies)
Hallo Ich habe schon einiges gelesen hier jedoch komme ich nicht weiter. also habe einen Mendelmax 2 gebaut und verwende dazu das Rumba Board mit den DRV 8825 Driver. Ich verstehe die Einstellung der...
View ArticleForcing continuous perimeters? (no replies)
I'm trying to print some part with thin walls, just two extrusion widths wide. By carefully modeling the object I get good results in most of the walls, but still in some areas the perimeters break up...
View ArticleZ Axis drives not syncing [i3] (no replies)
I recently bought a Gadgets3D i3 and have hit a bit of a snag that i cant seem to resolve through searching. the x & y axis move great, but the z axis has had a few problems, at first it would...
View ArticleBed en verre et ABS (no replies)
J'ai lu que certain avait pété leur bed en verre en montant à 110° du coups j'ose pas essayé l'ABS de peur de fendre ma plaque en verre. Comme je l'ai usiné a coups de dremel, ça m'embêterait de me...
View ArticleWelches Hotend für 0.25 ? Leider hat Stoffel seit langem nichts im Shop :-(...
Hallo zusammen, solangsam habe kein bock mehr auf 0.4 denn da die feinen ecken immer käse aussehen. würde gerne ein hotend mit 0.25 haben aber finde keins was schön ist. habt ihr da eine idee mit...
View ArticleModificare la velocità di un layers in gcode[RISOLTO]* (4 replies)
Buonasera, su una stampa di 4h c'è un singolo layer che manda in palla tutto a causa di uno "zigzag" molto stretto a ridosso di un ponte. Da Slic3r non riesco a limitarlo se non allungando di...
View Article