Printer is faster on first layer (no replies)
Hello, I'm facing a very strange issue, my printer goes faster on the first layer. At first I though that it was a problem with Slic3r inverting a parameter, but if I decrease the first layer speed...
View ArticleNouvel arrivant : Besoin de plastique! (2 replies)
Bonjour à tous! Tout d'abord je me présente, romain, je viens de finir mes études en ingénierie mécanique, et j'ai décidé de sauter le pas... même si mon compte en banque va faire la gueule pendant...
View ArticleTolerancie priemeru filamentu (2 replies)
Zdravím :) chcel by som sa len informovat s akou toleranciou priemeru filamentu pracujete ? Len pre porovnanie mne kolíše od krajných cca 1.6 do 1.9 ... 1.77 funguje pre mna asi najlepšie, pravdaže je...
View ArticleClik here to view.
RAMPS for Due! (3 replies)
I have been working on a prototype, porting code and its looking good so far. I have got comms, steppers going and just working on temperature control. There's a few snafus on the board that will need...
View ArticleSanguinololu not working standalone (no replies)
Hello, When Sanguinololu is attached to PC (USB cable) everything works perfectly. When I connect external 12V power supply everything is still fine. Finally I can disconnect USB cable and...
View ArticleExtruder Gear Grinding (6 replies)
Hello, I've started using a new extruder - one of the Greg's Wade extruder variations - on my printer a couple of days ago. So, this is the second set of extruder I've used/am using. The first one was...
View ArticleMendelMax construction alignment and warping? (no replies)
Hi, I've just finished the frame construction on my Blomker MendelMax kit, and I've noticed that now that I put the brackets on the tops of the A frames that the base was no longer flat on my...
View ArticleDremel sur hadron (no replies)
bonsoir ou bonjour , je viens de voir sur Thingiverse plein de chose pour ma dremel et j'aimerai bien l'adapter " voir vidéo [www.thingiverse.com] et autres
View ArticleOpenSCAD bug (no replies)
Any OpenSCAD developer around? When I press F5 on my model I get: OpenGL Program Validation results: Validation successful. openscad: src/csgterm.cc:191: void CSGChain::import(boost::shared_ptr,...
View ArticleHeatBed Help (1 reply)
So, I've heard that you don't need an MDF board for the Prusa 2, and somebody mentioned somewhere about it being a possible lung hazard, but all of the assembly instructions everywhere talk about...
View ArticlePrusa Mendel i2 parts version (no replies)
Hi, Sorry for the newb question.. I'm in the process of building a Prusa mendel i2 and getting all my parts (now a kit) before starting the build. I have the LM8UU berings and want to use them is this...
View ArticleDouble check my parts list before I buy my first build parts? (no replies)
Attached is my build list and sources for my first build. I am building a Prusa i3 with a box style frame. Any suggested changes to this list? are these quality parts? Did i forget anything? the...
View ArticleTake a look at my project! (no replies)
I'm new to blogging so please forgive me if I'm not doing this correctly. I just took some photos of my half pipe Morgan project that I've been working on in my garage and wanted to share them. I have...
View ArticleStepper motor rotates to one side - Help (4 replies)
Good night. I bought a RAMPS V1.4 and stepper motor drivers. Follow this video to set. [www.youtube.com] But, stepper motors are running sideways posstive when I press to run to the downside in...
View Articlesanguinololu board running low voltage motors (2 replies)
Hey guys! So I bought the Sanguinololu board. My stepper motors are rated at 2.8 volts and 1.68A. The Sanguinololu board accepts a 12 V input but in any case not lower than 7 volts. So my question is,...
View ArticleExtruder Heizung setzt für kurze Zeit aus! (2 replies)
Hallo Freunde, ich hab seit kurzem ein Problem mit meinem alten Prusa. Und zwar fällt seit kurzem meine Extruder Heizung öfters für ein paar sekunden aus. Dadurch sinkt die Temeperatur so weit ab, das...
View ArticleSlic3r & Dual Extruder T1 fördert zu viel (1 reply)
Hallo Mitstreiter - ich habe den Prusa I3 gebaut mit einem Dualextruder. Die beiden Extruder sind identisch bis auf das Düsenloch. T0 hat 0.35 mm T1 hat 0.5 mm. Ich benutze das gleiche Filament (3mm)...
View ArticleWiring up PSU (no replies)
I'm quite new to the forums (but a long time reader), and have decided to post a question I had regarding the electronics for Reprap printer I am currently building. I currently reside in Japan, where...
View Articlecouches abs non soudées..... (no replies)
Bonjour à tous, Il est des jours où l'on se demande pourquoi les choses ne vont pas bien.....:S J'imprime avec de l'ABS sur une Mendel90 paramètres t° hotend 245°C et lit à 110°C et le résultat est...
View Article