Ho collegato e montato Tutto! E adesso? (9 replies)
Salve a tutti. Ho appena finito di montare collegare, assemblare tutto. Potreste aiutarmi con qualche link passo a passo, ma molto a passo passo, per continuare? Collego alla corente:)...al mac...e...
View ArticleFilament Qualität beurteilen? (4 replies)
Ich suche eine Möglichkeit, die Qualität von Filament (nicht Drucker/Düse) zu beurteilen. Notwendige Drucktemperatur, damit die Lagen kleben -> http://www.thingiverse.com/thing:35088 Durchmesser,...
View ArticleSlic3r help (2 replies)
Hi, I don't seem to be able to get slic3r to infill small areas, see picture attached. Sorry about the quality. What is the setting I need to change to correct this? Thanks
View ArticleUsed to own a RepRap Huxley. Now I've started an entire local 3D printing...
Hi fellow RepRappers, I used to own a RepRap Huxley - my first 3D printer. I saw the need for local 3D printers and the positives for both owners of 3D printers, and for customers who need or want...
View ArticlePresets revert to wrong values on Save (no replies)
I'm having a problem with Slic3r, when I try to enter new values for things like "Bed Temp", "Perimeters (minimum)", "Solid Layers (top/bottom)", etc. The preset I have will say, perhaps, "1...
View ArticleHow to reduce blobs at line starts? (2 replies)
What are the best ways to reduce the blobs/lines that appear every layer in the same spot up the print? Would adding 2 perimeters help or reducing print speed?
View ArticleCurved bottom - any way to eliminate/prevent it? (2 replies)
I was finally able to print X carriage for Prusa i3 after three failed attempt. Because the way this part is oriented on the hot bed (I believe it's for better structural strength for the stress...
View ArticleAnyone else having trouble getting straight acme rod? (1 reply)
So I just received my second order from mcmaster the other day and my acme rod arrived practically bent in a u. I got it swapped and this new one is bent to, just a whole lot less. Is there a better...
View ArticleMaking the move to a Delta based printer.. Where do I find a tutorial for...
Ok, Its been a while since Ive messed with my firmware on my prusa printers. So I kinda remember how to set and calibrate those... But I have no clue where to begin in MARLIN to set it up for a...
View ArticleClik here to view.
dealing with ooze in slic3r? (no replies)
I printed the makerfaire robot and I noticed there is some ooze draping across the arms to the body at each layer which I then have to cut away. , I want to eliminate this extra goup if at all...
View ArticleATX PSU keeps turning off when I plug USB in? (no replies)
ATX PSU keeps turning off when I plug USB in? I have green lights on all the boards but i goto plug the USB cord to computer power supply shuts down. Bad PSU?
View ArticleForum Rules? (1 reply)
Hi all, Where's the list of the rules for this forum? Normally on forums I see them blatently thrown at you or at the top of some subforum (usualy the admin / announcements section), but can't I find...
View ArticleUConduit H-Bot 3D Printer / Reprap (no replies)
Hello all, Some of you are probably already aware of this printer from hackaday or the thingiverse page. I thought I'd also make a forum post for those who frequent these forums. The UConduit is a 3d...
View ArticleBFB 3000 Twin Head Printer on eBay (no replies)
Just in case it's of interest to anyone here: http://www.ebay.co.uk/itm/190886561869?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1586.l2649 Si
View Article(Automatische) Messung der Filamentdicke (10 replies)
Moin, da es ja sonst doch wieder keiner macht, nehme ich nun mal das Thema aus dem anderen Thread in dem es sonst nur untergeht und v.a. den Thread verwässert und starte hier einen neuen. Achim...
View ArticleClik here to view.
New 3D Printer with integrated 3D Scanner (5 replies)
We are the startup AIO Robotics and developed a new 3D copy machine. We created a 3D printer with an integrated 3D scanner. The idea is to have an all-in-one 3D printer that is capable of 3D scanning,...
View ArticleWax printing (2 replies)
Hi All, Just an idea to throw out there, perhaps plant a seed with someone. Many years ago (1988) there came out a range of Tektronix Phaser printers (Xerox took over the line and they also sell laser...
View ArticleI actually did it! (no replies)
I don't know if any of you can appreciate what this here means to me. It means that within the last three weeks I bought a soldering iron and tought myself how to solder. It means I found enough...
View ArticleUtilisateurs de Reprap en France (2 replies)
Salut, suite à une proposition de Kourou ce serai une bonne idée de se référencer sur ce site simple et efficace => mappemonde.net Ça va peut être faciliter les rencontres, sait on jamais ! ;-) Au...
View ArticleHall-o calibration (4 replies)
Hello, anyone know how I calibrate Hall-o endstops? I have them on the three home axis ends of the axis. They have the appropriate magnet pole facing the hall-o sensor which induces the LED to come...
View Article