Re: Buy Real Quality fake passports,driver's licenses,visas,ID cards,...
Or you can just go to the silk road or atlantis which has a feedback and escrow system and get not only fake ID's but any drug you can imagine.
View ArticlePronterface can't talk to Sanguinololu (no replies)
Hi all, Just finished building up my Prusa i2 to a basic level and wanted to test out the interface and motors. The problem I'm getting is that Pronterface can't communicate with the Sanguinololu and...
View Articlekalibrierung (3 replies)
hallo an alle, bin dabei meinen mendelmax mit kisslicer zu kalbirieren. bedlevel.stl und cube 20mm gingen gut, nachdem ich die flowrate auf 85% gestellt habe. babe jetzt den tower 50mm ausgedruckt,...
View ArticleHow to define pin numbers on marlin fw (no replies)
Hi everyone, im trying to make pin definitions of marlin firmware in pins.h file. But I saw this kind of definitions there, #define Y_STEP_PIN 60 #define Y_DIR_PIN 61 Arduino mega hasnt pin 60 or 61....
View ArticleRe: Buy Real Quality fake passports,driver's licenses,visas,ID cards,...
Fake as in you can't actually do any of that stuff.
View ArticleQual'è la stampante più economica che si vende in Italia? (no replies)
Sapete qual'è la stampante 3d FDM più economica che si vende in Italia? A che prezzo? Sapete se si vendono anche stampanti DLP in Italia, oltre a Robot Factory?
View ArticleClik here to view.
All 3D Printing Material anaynize (no replies)
The material make determination for the printing quality. So I make an summerize for all crrent market material here. Very glad with your honor instruction: 1. ABS or PLA. The high toughness and high...
View Articlereprap name for a domain name (2 replies)
Hey, i know it sounds wierd but i would like to create a website with the name 'reprap' in it, can i do that? is it open source or im gonna get sued? it there any restrictions for selling reprap...
View ArticleStepper, torque, volts, pps (1 reply)
Hi all Trying to make some sense of this Objective : maximize torque and rpm and validate my (mis)conceptions Application is non reprap Motor :wantai nema 23, type 57byg621 torque curve attached...
View ArticleExtruder läuft nicht vorwärts (2 replies)
Hallo, ich habe das Problem, dass irgendetwas in der Konfiguration falsch eingestellt zu sein scheint. Der Wadeextruder setzt geschätzt 2mal die Sekunde das Filament zurück. Dadurch bewegt er sich...
View ArticleMounting North90's Hot End V2 to Wade's Extruder (no replies)
I have been spending the last two weeks or so assembling a Prusa Mendel, and have reached the point where I must attach the extruder and hot end. I chose North90's Version Two due to the ease of...
View Articleprintrboard electronics (2 replies)
Quiero ver quien me puede ayudar envez de comprar Ramps me compre una copia de printboard porque tiene varias ventajas como la ausencia de un chip ftdi o la posibilidad de implementar correciones en...
View Articlemoderator-only subforum? (2 replies)
VDX has tried to help me get used to this ancient and badly written software, but without some tools or additional help I'm lost. Is there, or can there be a forum that only moderators can see and...
View Articlebridging - can this be bug? (2 replies)
Hi, I am new to reprap and trying to calibrate my printer and I found something strange with SF 50. I have 0,5 nozzle, print at 215°C ABS, layer 0.3, feed and flow are set to 30, bridging feed to 0.7...
View Articlecant get start g code to work - need help again (2 replies)
Ok so in here with my hat in hand again. I have everything working except i can not get the start.gcode to load into the header when i slice a model. I have it enabled under Alteration, and i have the...
View ArticleUsing resistive foil for heated bed? (3 replies)
Has anyone tried this? I have found this on my local electronics parts supplier: [www.gme.cz] (sorry, it's in Czech, I was unable to find any equivalent in English) and wondered, if it could be used...
View ArticleOff topic! (2 replies)
There you go Chris, that nice Mr. Gove has said that all children should be taught how to use 3D printers. I reckon that means a Mendel90 in every school. You're going to be a rich man!
View ArticleZ Axis Problem (2 replies)
Attached is my Marlin firmware file Currently running RAMBo electronics on a Prusa Mendel. All motors were operational for the last few days. No major changes made to anything. Z axis motors just...
View ArticleHot end wont heat up. Please help! (2 replies)
My friend gave me his Pusa Mendel Iteration 2, I'm running sprinter. My electronics are RAMPS 1.4 with Arduino Mega 2560. I have connected the printer to pronterface, (btw Im using a Mac Mini) I am...
View ArticleHotend Problem with Ramps (no replies)
I'm having some issues with my thermister. Pronterface is telling me I have a temperature of 0 degrees. I have tested the contacts on the thermister and I am getting 100k ohms. I've been told on the...
View Article