[USA] Complete Prusa i2 kit 650 (no replies)
I have a couple Mendel Prusa i2 kits for sale that come with everything except plastics. I am selling kits for $650 + $53S/H. I can print a set of plastics for you if you like, or I could fully...
View ArticleRe: Details lost and strange anomalies added after slicing (no replies)
Hello, Anyone have this problem with Slicer that I am having. I load an STL into Repetier and the detail on this STL looks great. Then I go to slice it and a lot of important details disappear, and it...
View ArticleIntermittent Sleep (no replies)
I've built a i2 Reprap prusa mendel with a card reader and LCD display etc for stand alone printing. However occastionaly my reprap goes to sleep. There is no sleep commands in the gcode and with my...
View ArticleMoin moin aus HU (no replies)
Hier mal ne Anfrage bzw eine Idee für Repetier. Ich vermisse ganz dringend im Repetier-Host und warscheinlich auch in der Firmware einen Programmpunkt, um bei Ausdrucken von mehreren Teilen wärend des...
View Articlecan,t connect with arduino (no replies)
Hello guys, i'am trying to calibrate my prusa. I have a sanguilolu 1.3a. when i want to upload the compiled file i get the following message: avrdude: stk500_getsync(): not in sync: resp=0xed i've...
View ArticleNozzle came out of the holder (no replies)
I have been having some really bad luck with the printer ... but it just got much worse. The nozzle has just blown off the holder and is covered in PLA. It was printing ok when I left it but when I...
View ArticlePiece on the Gada/Uplift Prize for 3Dprintingindustry.com (no replies)
Hi folks, I'm a writer for 3dprintingindustry.com and I'm doing a short write-up on the Gada prize. I've been doing a quick look around the forum and am having a hard time with the organization of...
View ArticleAdvice on mk7 gear set screw problems (no replies)
Hi guys ths problem s doing my head in I'm using i3 extruders that use the mk7 gear pully to grip the filament The problem I have is my stepper motor skips , filament stirs and skips the lot I rip the...
View ArticleRepRapPro Mono Mendel (no replies)
Does anyone have any experience dealing with the company RepRapPro, or know any of the contacts there. I recently bought their Mono Mendel version of the RepRap and am in the process of the build. I...
View ArticleHow to set up the 5th pololu to power the 2nd z stepper (no replies)
Well it may be a dumb question, but... Is there a way to setup Marlin so I can use the 5th pololu to power up the 2nd Z stepper, so I can run them colder? Thanks!!!
View ArticlePitch of t2 timing belt (2 replies)
I ordered a t2 timing belt with pulleys, and installed it on my printer. I now have all my electronics wired, I have noticed that the printer is not traveling the right distance when I tell it. I got...
View ArticleKossel Pro - Automated bed detection and levelling (1 reply)
Not sure if you seen this but on Kickstarter there is a Delta Printer that has automated bed detection and leveling...
View ArticleConvert SCAD to Solidworks? (4 replies)
Hi, I'm new to 3d printing (still waiting on parts to arrive to build my prusa i3) I'm experienced with Soidworks and prefer to use that over openscad as it makes sense to me. Is there any easy way to...
View ArticleInkjet printing on PLA or ABS (1 reply)
Hey RepRap I just had an idea hit me, and I wasn't sure if the 3D printing community had tried it yet. Could a inkjet printer cartridge be attached adjacent to the nozzle, then be used to dye the...
View ArticleA few blown up PSU's , PLEASE HEEELLPPP!!!!! (2 replies)
hey, if somone can please help me, I've blown up 2 atx2 power supplys , cant seem to understand why this happens , I use a modified pololu electronics board it only connects to the ground and the +12v...
View ArticleZ axis motors not working at all, but all others are (1 reply)
The Z axis on my reprap Prusa mendel i2 makes a buzzing sound when I try to move it. I have adjusted the pots on the controller all the way from one end to the other and it does not move at one end...
View ArticleRepetier-Host 0.90 beta windows Feedback wanted (no replies)
Hello, I'm finished with all intended features of the next host version. Having made quite a lot of changes, I would like to get some feedback if everything works as expected. You can get the beta...
View ArticlePronterface funktioniert wieder mit einer Gen7 (no replies)
Seit gestern kann man Pronterface wieder für eine Gen7 verwenden. Genauer, für Elektroniken, die den Gen7 bootloader verwenden. Pronterface kam damit nicht klar, weil es immer versucht hat durch...
View Articlehotend blocking filament (2 replies)
cant do any good print since first day on my prusa i3 The hotend keeps blocking the filament. i dont know how to fix it. i am using the g3d Budaschnozzle style hotend why cant i get an uniform...
View ArticleSir Spam Alot (1 reply)
Seems recently theres been alot of spam bots on this forum for instance Warren mandal hes alover the place youtube alsorts is there nothing we can do to stop bots from happening
View Article