Greg's Wade Reloaded and 1.75mm filament (no replies)
Having done my research into the 3mm vs. 1.75mm debate, I've landed on the side of the latter--primarily due to my experience using it on a Makerbot Replicator at the office. With that said, I'm...
View ArticleFehler beim slicen mit dem neuen slice3r mit repetier (2 replies)
Ich habe ein Problem das mit den umstellen auf die neuste repetier Software meine Bauteile die vorher ohne Problem gingen jetzt nicht mehr geslict werden können da sie angeblich Löcher haben haben....
View ArticleClik here to view.
inMoov prints ? (no replies)
Just wondering if anyone from the RepRap community has tried printing the InMoov humanoid robot ?
View ArticleLayer Löchrig wie ein Sieb (5 replies)
Hier gehts zum Bild Ich hoffe man kann es erkennen, weis jemand woran das liegt?
View ArticleTraslazione asse Y su prime stampe (1 reply)
A cosa potrebbe essere dovuta questa traslazione di layer? Specifico che avviene solamente sull'asse Y dato che sull'asse X la situazione è pressoche perfetta...Premetto che doveva essere un cubo......
View ArticleFinished my prints (no replies)
I have finished my prints and have the extrusion and rods on hand waiting for me. I am curious as to what hot ends can be used with the foldarap. Are there alternatives to the original. I am ready to...
View Articlecollegamento cavi motori (3 replies)
La sequenza di collegamento è rosso-blu-verde-nero, ma come vanno orientati? Qui il rosso è verso dx, mentre qui è verso sx Quale è il verso corretto di collegamento dei cavi dei motori alla ramps?
View ArticleComment installer un Firmware sur RAMPS 1.4?? (1 reply)
Bonjour, Je suis utilisateur d'une " vraie " Imprimante 3D a mon travail, et je souhaite faire mon propore system à dépot de fil ( à ne pas confondre avec une imprimante 3D.... !!!! ) Je suis nouveau...
View ArticleConsiglio su come migliorare la nostra RapidBot (1 reply)
Salve a tutti. Alla fine siamo riusciti a far partire la nostra RapidBot 3.0...anche se il risultato non è dei migliori fin'ora. Dobbiamo metterci giu a settarla per benino. Essendo neofiti, abbiamo...
View ArticleSlic3r error (no replies)
I had walked away from my printer for a few months and when I came back everything would work, but when I hit print nothing would happen so I downloaded the new pronterface software now I get the...
View Articlepossible electronic rep rap? (no replies)
What about UDOO, there's anyone currently coding to get Arduino Due working with RAMPS or Marlin stuff>?(tu) have a look [plastbot.wordpress.com]
View ArticleClik here to view.
Taulman 618 bonds too well to print surface?!? (no replies)
So. Finally, I got some fabric-based laminate board for printing the Taulman 618 filament on to. The product I got is probably not exactly Garolite (being based in Europe, I ordered it from here:...
View ArticleSigns of a failing Thermistor? (no replies)
Hi, I'm printing now for a few weeks with the G3D Budaschnozzle and I've had good results. Now since a few days I have some weird effect in my Repetier Host, the temperature goes up less quick than...
View ArticleNew problem - Motors don't move after fixing end stops (1 reply)
Greetings all, Thanks again to those who helped me work out the end stop issue. Putting one end-stop per axis in the proper place allowed the end stops to return correct values with M119. Thing is,...
View ArticleNabídka ABS (no replies)
Známej objednal nějaký ten materiál, tak pokud by byl zájem .......na rychlo jsem mu spíchnul eshop. Mělo by to tu být začátkem příštího týdne. O kvalitu nemusí být strach, tisknu z toho a je tam...
View Article3D cement printer (3 replies)
3D Cement Printer I am prototyping a cement printer. So far, I have the first version. It’s 1/3 of full scale and the major parts are done. I have Arduino and RAMPS for the brain and Toshiba James...
View ArticleNema motors (no replies)
Hello to all. I want to build Prusa i3. Can I use Nema 17 motors with 19.6 N-cm holding torque for it, 12V power supply. Thank you.
View ArticlePoor Print Quality (1 reply)
I have been working on getting my printer up and running and I have finally had some success. The prints are very poor quality, usually around 2mm up on the z-axis it begins to drift to one side, but...
View ArticleRapman 3.1 pressure bearing issues? (no replies)
I recently acquired a rapman 3.1 printer, and it is almost working except for one problem: it doesn't feed reliably. It uses the screw-drive type system and the pressure bearings seem to need constant...
View ArticleClik here to view.
Problem with the nmb stepper pm35s-048 (2 replies)
Hi fellow: Im posting this because I dont have a typical circuit test for this steppe. So I decided write an e-mail to company for support if they have the schematic circuit, BUT i had respond from...
View Article