Programmi per stampare quali sono ? X( (no replies)
Salve a tutti :) O praticamente quasi finito di costruire la mia stampante 3D e ho voluto fare una stampa a vuoto per vedere un po' come si comportava e devo dire che sono veramente rimasto...
View Articlewiring xbox PSU+relay+RAMPS 1.4 (2 replies)
Hello everybody, I bought a reprap kit two weeks ago composed by all the mechanics fully assembled, an arduino Mega 2560, a RAMPS 1.4 shield and a XBOX PSU 203W and a relay. I have some little...
View ArticleProblem setting up (no replies)
I'm trying to get my new Prusa Mendel 2 working these days. Now here's the case: I connected all those wires on the boards and PSU, but when I wanted to try a little bit, (the lights on Ardino board...
View ArticleSometimes is the simplest of things that cause problems (no replies)
I print in ABS and it's very rare for me to have adhesion problems. Last night I kept having the corners of a thin plate lift and that is just odd with my printing. Ends up when I designed the item I...
View Articlebuild plate adhesion surface (no replies)
Hi, I found this new thing called BuildTak. It's apparently a build plate adhesion surface that works. Found some reviews, some good, some not too good. But apparently it works. And doest seem too...
View ArticleFirmware update problem (2 replies)
Hello, I am trying to update the Arduino Due firmware as prescribed on the reprappro website but with no luck. ( I am on a mac) When I type a command into the terminal to run the firmware upload...
View ArticleExtruder (stepper motor) fan control (no replies)
Hi there, i am looking for a way to turn two fans on or off. When steppemotor0 is on Fan0 goes on. And when steppermotor1 is on Fan1 goes on. I can control the fans with M106 S255 and M42 P6 S255. But...
View ArticleChina OLED materials supplier (no replies)
Product SpecificationsFormula：C16H12O5Weight：284.26CAS No.：491-80-5Thermal Gravimetric Analysis：Absorption：Photoluminescence：Grade：>99.5%Availability：contact usE-mail: sales@hanshangchem.com,...
View ArticleRepetier host V.95 E and F (no replies)
Greetings, I have upgrated to host V95 E and then .95F, along with firmware v.91 on Azteeg X3 running a mill. When I attempt to run g-code I had run successfully on earlier version, I get the...
View ArticleError compiling .91 with SDCARD (no replies)
This is the error: SDCard.cpp: In constructor 'SDCard::SDCard()': SDCard.cpp:44: error: 'DIOSDCARDDETECT_DDR' was not declared in this scope SDCard.cpp:44: error: 'DIOSDCARDDETECT_PIN' was not...
View ArticleLooking for a new filament supplier - whts your experience. (4 replies)
Hi , after countless wasted hours, I've had a gutsfull of cheap china filament. Whats your recommendations, mainly for PLA.. I have been using Reprapper... its so inconstant in diameter etc.. looking...
View ArticleProdam 3d tiskarnu Prusa i2 v Brně za 12 500 Kč (no replies)
Dobrý den, prodám kompletně sestavenou a funkční tiskárnu Prusa i2. Elektronika: Arduino Mega 2560 + Ramps 1.4 + 4ks StepStick čtečka Sd-karet, displej 16x2, encoder FW Marlin Motory Microcon SX-1005...
View ArticleEuropäische Händler (8 replies)
Moin Moin, ich habe in den letzten Tagen sämtliche Komponenten für einen Mendelmax bestellt. Allerdings habe ich 4 Kanditaten dabei die, falls sie vom Zoll geprüft werden, zusätzliche Abgaben...
View ArticleValore della stampa 3D (13 replies)
Visto che facciamo servizio di stampa 3D ci siamo imbattuti, tramite un cliente, in un preventivo di altrettanto servizio che reputo "alquanto raro" Secondo voi è proporzionale una stampa in abs...
View ArticleExtrusin calibration (2 replies)
I think I am extruding a bit too much as holes etc. in my parts are slightly too small, and pins slightly big. The feed is correct (100mm feed is exactly 100mm of filament). I saw that there is a way...
View Articlemelt / sag print head easy fix (7 replies)
Hi, Some of Ormerod users experienced overheat screws which will melt the print head holder . I apply silicone heat transfer compound in between cooling block surface and heat sink. The heat from...
View ArticleF2 fuse burn (2 replies)
Hi all, i just finished mouting a prusa i3 3D printer. everything was working well (all motor move in the correct direction) untill I want to heat the hotend and the heatbed to began my first print....
View ArticleConseil PLA (no replies)
Bonjour, j'utilise du PLA et je voudrais savoir s'il y en avait de différentes qualité et où l'on pourrait se procurer les bobines PLA de bonne qualité.
View ArticleWant To Buy Prusa i3 Hardware Kit (no replies)
Hi! I'm looking for a hardware kit for the Prusa i3. i already built a i2 but have disassembled it. I have motors and all electronics, I just need the printed parts, laser cut parts, vitamins and...
View ArticleNEMA17 (7 replies)
Hallo medeprintertjes(:P) welk typenummer staat er op jullie motortjes?? ik heb zelf de 42BYGHW811 maar die word niet veel aangeboden op ebay dus hoop op een andere oplossing hoor het graag greetsz...
View Article