Clik here to view.
New Ormerod Web Interface - WIP (6 replies)
Began work on my new Web Interface for the Ormerod, Design pretty much complete, moving onto the functionality now.
View ArticleGetting odd marks on prints (1 reply)
Overall I'm pretty happy with the quality of prints but seeing more of these little points sticking out. In the first pic attached they are quite clear and on the second picture, the other side, it...
View Articleerror (1 reply)
Hola pruseros¡¡ me llamo Álvaro y soy de A Coruña, he construido mi prusa i3 hace un par de meses y todo iva de prusa madre hasta que quise desmontarla para reorganizar el cableado y sorpresa; :...
View ArticleClik here to view.
Slicing problem (no replies)
I'm having a problem with Slic3r - I can't see anything wrong with the STL file and Slic3r is not consistent in how it messes up this part. Here is a screenshot showing the G-code - the two flat...
View ArticleMotory na ose Z se točí, jak chtějí (11 replies)
Zdravím, mám takový problém. Na ose Z se motory točí, jak chtějí. Když manuálně zadám, ať se osa zvedne nahoru, tak se motory občas točí dolů. Někdy se točí správně, ale po chvíli změní směr. Něco...
View ArticleConfigurando Prusa i3 - Ayuda! (4 replies)
Hola Estoy tratando de configurar mi prusa i3. Tengo todo montado. los pololus los tengo con Vref 0.370 X e Y se mueven mucho mas de lo que le indico al pronterface. Le digo que se mueva 10mm y se...
View ArticlePSU Cutting out... (10 replies)
Hello All I don't seem to be having much luck here... I got to the "Orthogonal Axis Compensation Test" stage where it did a few layers and then the PSU cut out and only the 1 LED was lit on the ATX...
View ArticleClogged Hot End (2 replies)
Finally got to testing my mendel90. I was about to calibrate my extruder, but it failed. I could not get my extruder to extrude. I has the temperature set to 185 as described in the manual with the...
View ArticleMargin of error? Or did i get ripped off? (6 replies)
Hello, I bought the printed parts for a Mendel I2 on ebay about a month ago, and have been building it ever since - acquiring additional vitamins as i went along. I had a terrible time getting...
View ArticleTaulman printen op .......?? (1 reply)
Ik heb vandaag mijn eerste Taulman binnengekregen. Op de website staat dat het niet hecht op alu of glas. Ik print mijn PLA op heated glas. Waar printen jullie het op ? Zijn er meerdere alternatieven...
View ArticleSlic3r and Support for a specific Model (1 reply)
Hello Guys, I try to print a Mario figure with support but unfortunately ... it will make the support everywhere, is it somehow possible to force the support only under the arms ??? not @ the center...
View ArticleAdvice: Avoid this brass for your hobbed drive wheel (4 replies)
This is my experience with brass as a drive wheel. I hobbed this naval grade 485 brass from Mcmaster Carr. The teeth are too soft and collapse, and break off, thus jamming the nozzle. I did have a bit...
View ArticleMegatronics v 2.0 - servo z axis - Marlin - help (no replies)
Ciao, qualcuno può aiutarmi a configurare una megatronics v 2.0 con un servo per la calibrazione automatica del piano? non so nemmeno dove attaccare il pin del servo e come attivarlo in Marlin....
View ArticleRumba short circuit (no replies)
Hey guys, i recently burned down my Rumba Board caused by an short circuit between the fan and the Motor. As i got a Black Rumba i can´t really see what exactly burned down, but it seems like its the...
View ArticleTrying to find a stepper motor under 1A but with enough torque (no replies)
I'm having extreme difficulty finding stepper motors to buy. My drivers are only rated for 1A, but every motor I can find has the torque drop significantly once you go under that. I must be...
View ArticleResin Alternative (1 reply)
Hallo zusammen, Ich suche nach einer Alternative für das von Formlabs überteuerte Resin. Ich habe viel gegoogelt und bin zu dem Schluss gekommen das ich es nicht selber herstellen kann .Dann bin ich...
View ArticlePrintrun Freezes when unused with Mac (no replies)
Hi, I just discovered a problem with the printrun functioning on a Mac with Mavericks 10.9. The new Mavericks version has a setting for each application that allows it to be put to sleep. I didn't...
View ArticleClik here to view.
[HELP] RUMBA burned (no replies)
Hello, Today I sadly had the idea to update the cable that goes from the DC power to the Rumba board, I switched the polarities by error and when I turned on the printer I saw a smoke puff. Quickly I...
View Article[Help!] Could someone slice something for me please. (no replies)
My Nephew has found a model on thingiverse and asked me if I could print it for him. I usually use slic3r, but it's just not happy with the model. I could try to use skeinforge, but I'd have to spend...
View ArticlePrusa iteración 3 por donde empezar? (no replies)
Bueno pues eso quiero construir una Prusa iteración 3 que e visto que sus modelos de impreson son 20x20x20 (creo recordar ahora) y bueno buscaba una impresora facil de montar y que a la vez se pueda...
View Article