Easier extraction from heated bed? (1 reply)
Sometimes my print becomes absolutely GLUED to the print bed. What sort of methods do you guys use for extracting from the heatbed that is a little quicker
View ArticlePrinting from an Ipad? (1 reply)
Does anyone know of any APPs or anything that would let me print from an Ipad or a tablet?
View ArticleAnfängerfragen zur Elektronik (3 replies)
Hallo, ich habe mich schon ein wenig eingelesen, ein paar fragen habe ich aber noch: Mit der Melzi elektronik benötige ich keine weiteren Teile am Drucker, ist das richtig? Die wiki sagt: QuoteMelzi...
View ArticleKossel printed parts needed.midlands.UK (no replies)
Can somebody help me with printing parts for me ( will pay reasonable money) will be full set of parts. STL will provide. Our community is growing slowly but steady thanks to helping out each other Thnx
View ArticleHow to hold the bed down? (3 replies)
Has anyone found a good way to hold the print bed firmly on the heat spreader and not slip? The foldback clips don't work for me even if I just clip them over the edge, because on the end of the bed...
View ArticleFaire briller le Pla (no replies)
La grande question bon j'ai pas inventer l'eau chaude!!! Mais en passant avec un pinceau un mélange résine époxy et cathaliseur j'ai obltenu un bel effect brillant et un objet lisse. Voir photo.
View ArticleClik here to view.
Which plastics??? (no replies)
Hi Guys\Gals... Well I finally got the spare funds together to build myself a printer and have set my mind on a single frame prusa i3. My confusion has set in pretty quick with regards to which...
View ArticleTOTAL CONFUSION!! - Possible Programming Issues (no replies)
Hi peoples, I started building my very first Prusa Mendel I2 that i had purchased from amazon [www.amazon.co.uk] (3rd party dealer) at the start of December. Give or take 3 -4 days later (after work )...
View ArticleTemperature (5 replies)
Hi EveryBody, I have Ormerod from rs NO:408, I have some problem with the sensor of temperature. If I open pronterface and send M105 i get this message: Temperature measurement fault on heater 0, T =...
View ArticleWhich 3D printer to build? (5 replies)
Hi! I've been researching 3D printers and I'm still having trouble deciding on one so I was hoping I could get some help here. Which printer would do you think is best for a newbie to build with AND...
View Articleincrease print resolution by increasing stepper resolution possible? (1 reply)
Hi, I'm designing a delta printer for high precision printing and I'm wondering if adding a planetary gearbox with ratio say 100:1 which decreases the stepper angle of a NEMA 17 motor of 1.8 degrees...
View ArticleList of open designs? (2 replies)
Hello, i've built a reprap and i love it! However, now that i've started learning to model my own 3D objects i've realized how limited the machine actually is. A DLP printer seems to be the obvious...
View ArticleWhy did my Afinia printer create this mess? (1 reply)
I've only printed a couple of things with this new Afinia printer. The calibration model printed ok a couple weeks ago. Tonight I tried to print this model of the Enterprise: [www.thingiverse.com] I...
View ArticleSoCal RepRap Meetup (Jan 25) (no replies)
There will be a RepRap meet up on Saturday, January 25 at 2:00 PM at the 23b shop in Fullerton. 23b is a hackerspace in Fullerton, CA, that has milling machines, electronics workstations, meeting...
View ArticleMechnical design-CATIA V6 (no replies)
CATIA v6 2009 best for mechnical design, surface game design software.i think no other software compare to these software.whats your opinion friends??
View ArticleAnyone built a cooldrv stepper driver? (no replies)
I recently built a set of cooldrv stepper drivers with the drv8825 drivers and tested them on my sanguinololu and ramps electronics and with both, the motors turn much slower and seem to grind /...
View ArticleLast 2 Layer too slow Speed (no replies)
Hi guys, I'm having some trouble slicing with Skeinforge, all the print goes well but when it arrive at the last 2 (maybe 3) layer the speed is considerably decreased, with a bad printing as a...
View Articlerepetier-host 0.95c (4 replies)
E' uscita l'ultima versione di repetier per windows ci sono alcuni miglioramenti sul rendering dei modelli e pare essere più reattivo. cosa importante nello slice con slic3r si possono variare alcune...
View ArticleWer druckt mir ein ABS Fanduct in Kiel oder Umgebung (no replies)
Hallo ich suche jemanden der mir einen ABS Mendel 90 Fanduct druckt, möglichst in Kiel oder Umgebung. MFG Kielkarl
View ArticleClik here to view.
Broken extruder (no replies)
So this happened :( IMG_0487.JPG Stupid me didn't bother to print extra parts as one of the very first things I did. I think I can patch it back together long enough to print a new extruder, but i'm...
View Article