Clik here to view.
Problemas con montaje MendelMax 1.5, no hay tutoriales de mi versión??(td)...
Muy buenas, señores. No tengo mucha experiencia en este tema y he tenido un problema que espero que pueda resolver. Adquirí mediante una web española de impresoras 3D (de lo cual me arrepiento...
View ArticleHeat bed problem (tried everything) (5 replies)
Hello, I have a prusa i3 8'' bought from makerfarm. All the prints are in ABS. I got Ramps 1.4, atx power supply 500 watt (20 amps on yellow wire, i got 2 in each slot). I got a problem since the...
View ArticleSo I want to upgrade my hot end but I have questions (no replies)
I'm getting ready to re wire my Prusa I2. The are some ghosts in the wiring job the previous owner did and Im tired of them. I figured while I was at it, I would upgrade from the original...
View ArticleJ-Head PTFE Issues?? (1 reply)
Hi all, I have a J-Head MK-V using 1.75mm filament and im having issues with the PTFE liner pulling itself out of the J-Head when i retract the filament. Is there a way to stop this? i.e a washer or...
View ArticlePortuguese Community (no replies)
I see that the Portuguese community is death. I can try to give some life to it and start the wiki in pt if you want so.
View ArticleNema 17 Schrittmotor (4 replies)
Servus ich bin grad auf der Suche nach Nema 17 Schrittmotoren. Dabei durfte ich feststellen, dass es da ja viele verschiedene Nema 17 gibt. Was jetzt bei mir wiederum die Fragen aufwirft: Was nehmt...
View ArticleAchat groupé de filament, ça vous dit ? (2 replies)
Bonjour à tous, Je viens faire un petit sondage auprès de la communauté concernant l'organisation d'achats groupés de filament. J'ai déjà monté une mini boutique spécialisée dans la vente de filament...
View ArticleRamps 1.4 d2 pins for12v extruder fan, polarity? (no replies)
Hello I am almost finished with my prusa i3 build (graber) lasercut edition, with ramps 1.4 electronics and I have a quick question: Does the 12v extruder fan that is supposed to connect onto d2 12v...
View ArticleProblem with z axis (no replies)
I posted this on the ramps forum and got no response. I have run the ramps test program and everything works fine, yet after I loaded up Repetier firmware and connected to the printer with...
View ArticleTB6600 wiring help (no replies)
kindly someone help me in wiring a ebay tb6600 board to parallel port i am having doubt in EN- and pul- [www.ebay.com]
View ArticleGen 7 1.4.1 Probleme (2 replies)
Hi, ich habe das Gen7 1.4.1 habe nun leider ein Problem Es ist ein neuer Atmega 644p 20mhz drauf Das Testprogramm, mit der Blinkenden Led läuft super Netzteil an Led an, aus .... Netzteil aus fertig...
View ArticleClik here to view.
Printed Parts (3 replies)
Ordered printed parts from Ebay. This is my first experience holding a printed part and I have to say that I'm disappointed. This the first time I've held a printed part in my hand so I'm trying to...
View Article8 volts en sortie alimentation S400-12v (no replies)
salut tous, voilà je n'arrive pas a dépassé 8 volts en sortie alimentation S400-12v livrer avec ma ordbot et encore c'est en tournant le potard pour arriver a 8.71 V !! on ne peut le tourner qu'un peu...
View ArticleClik here to view.
3DR "Simple" Delta Printer (2 replies)
I have a Printrbot Simple I haven't used since I got my MendelMax 2.0 up and running. So I've been thinking about what to do with it. Then RichRap introduced his 3DR printer. I thought this would be a...
View ArticleHot end temp issue (1 reply)
Just finished building my reprappro mono mendel and everything seems to be working fine apart from the hot end. when i set it to 100c it goes up to 27 and then stops, and wont go any higher regardless...
View ArticleHot end temp issue (1 reply)
Just finished building my reprappro mono mendel and everything seems to be working fine apart from the hot end. when i set it to 100c it goes up to 27 and then stops, and wont go any higher regardless...
View ArticleHeatBed shuts down after 70ºC (2 replies)
Hello I've got a Prusa i2 with a 30A 12V power supply and i've been printing with PLA for a couple of weeks without a problem, but last night i tryed printing with ABS for the first time. I ajusted...
View ArticleY-axis displacements (1 reply)
Helllo everyone! I've finished assemblying my Mendel Tricolour couple months ago and didn't face with this problem until last few days. Like you can see on the picture, there some displacements on the...
View ArticleServo Motor (no replies)
Hello, I'm a little bit confused because I bought a DC Servo Motor Actuators (http://www.thorlabs.com/Thorcat/17600/Z812-Manual.pdf) and I like to control this motor with an Arduino UNO Microcomputer....
View Article[invitacion] demo en feria de matematicas (2 replies)
Estimados, viernes (de 10:00 a 19:00), sabado y domingo (de 14:00 a 20:00), estoy en el centro cultural recoleta, de capital. Hay una feria de matematicas a la cual me invitaron a participar con mi...
View Article