Marlin y lcd problema (4 replies)
A alguien le paso lo que me pasa a mi con el lcd y marlín cargado? Me aparecen todos cuadrados... Ya no se que probar. Supuestamente lo configure bien.
View ArticleClik here to view.
fil bleu ABS qui casse (2 replies)
bonsoir, j'ai un soucis de cassure sur cette bobine de fil ABS 3mm,quand je l'entre dans l'extrudeur normalement sans forcé ça casse! voyez vous sur les photos les traces blanches régulières ? avez la...
View ArticleOrdbot en Bowden (no replies)
Bonsoir,ça faisait un moment que je voulais passer la orbot en bowden,c'est chose faite. Voila 3 photos du systeme. [docs.google.com] [docs.google.com] Pour info,la hotend c'est du DIY,c'est la 2eme...
View ArticleSfat (no replies)
Salut, Sunt din Brasov si as fii interesat de un 3D printer. Am de gand sa ma apuc sa o fac eu. E indicat? Cunostinte de mecatronica nu am, doar tutoriale eventual. Ce model sar putea face cu...
View ArticleRamps1.4 on TAZ (2 replies)
I recently built a TAZ and I am using Ramps1.4. All works good, but the arcs show really rough segmentation and the printer is running rough on arcs. Same firmware setting on a smaller prusa is very...
View ArticleMore than extruding filament: PRINTING FILAMENT ! (no replies)
It means that you design a stick or a roll and your print it with your 3D printer ! and then you use the filament you just printed to print something ! ... such as the filament you just used !...
View ArticleVolumetric extrusion? (1 reply)
Is there a reason to why almost no one (so it seems), is using volumetric extrusion, instead of the classic way of having both e-steps and filament diameter. I followed Triffid Hunters exellent guide...
View Articlewonky hot end (no replies)
My hot end is wonky. I've tried removing and refitting to no avail. I think the two small springs are causing the mis-alignment. Anyone see this ? Cheers Rob J [attachment 18076 hotend.jpg]
View ArticleClik here to view.
dual aangedreven extruder (no replies)
Op mijn blog heb ik nog een leuk artikel geschreven over een dubbel aangedreven extruder die snelheden kan halen van rond de 900 mm/s. Zal de kwaliteit wel niet ten goede doen maar goed. Kijk maar...
View Articlever 0.90.c incorrect version.txt (no replies)
A small error: the linux v0.90c version.txt file states the version is0.84.
View ArticleBUG: unable to connect to printer (no replies)
v0.90c on ubuntu is unable to connect to my printer (sanguinolulu). It just says 7 commands waiting. I ran configureFirst.sh without testing if it worked before this. v0.85c is still able to on the...
View ArticleBewegliches Filament gesucht (1 reply)
Hallo liebe Community, ich bin auf der suche nach beweglichem Filament. Woher bekommt man bewegliches Filament? Ist es PLA oder ABS? Gibt es Probleme beim drucken? Und noch eine ganz andere Frage...
View ArticleUsing RepRap for copper engraving (no replies)
I'm curious to hear from anyone who's done this before... It's quite easy to remove the hot end and extruder from my Prusa and I can put something like a Dremel rotary tool or engraver in place with...
View Articlehilfe bei druckeinstellungen (2 replies)
hallo an alle, habe meinen vergrößerten mendel90 mit 360x300mm druckbett fertig. er läuft ganz gut, es gibt aber noch ein paar probleme.... habe obiges teil in 40cm länge, 14mm breit/hoch ausgedruckt,...
View ArticleMarlin min_software_endstops auswirkungen auf negatives Z offset (1 reply)
Ich habe Marlin auf meinem Drucker installiert, und frage mich ob die Einstellung min_software_endstops true verhindert, dass ein negativer Z offset Wert unter Slic3r funktioniert. Ich könnte das zwar...
View Articleproblemy s extruderem (7 replies)
Zdravim vsechny, v posledni dobe vcelku dost resim problemy s extruderem. Konkretni problemy jsou velikost nozzle 0,35 a bowden :) Diky teto kombinaci je problem s vyvinutim potrebneho tlaku, aby byl...
View ArticleClik here to view.
Problèmes avec le Support material (5 replies)
Bonjour, je suis en train de tester avec slic3r, le support materiel. j'imprime un dôme, que j'ai divisé en 4 parties. j'ai 5 mm entre chaque support. voici mes reglages vitesses comme vous le voyez...
View ArticleComprare Blue Tape e Kapton (2 replies)
Ciao a tutti mi servirebbe sapere dove posso comprare (in negozio o on-line) sia il nastro blue Blue Tape sia il nastro Kapton. Grazie a tutti!
View ArticleMy heated bed stopped working... (3 replies)
Hi everyone, I've tried searching but am yet to come across anything to solve the issue I'm having (not that I haven't tried all the solutions anyway lol) I've got a 12V power supply going to a RAMPS...
View ArticleSolving CPU overheating problem (1 reply)
After tidying up the wiring I had a strange CPU overheating problem with my printer electronics. The problem turned out to be a general one that is not related to a specific CPU or electronics board....
View Article