PM system problems? (2 replies)
I've noticed that when I reply to a PM in the forum system sometimes the reply doesn't make it to my sent folder. The most recent time I double checked when sending, and it said that the message was...
View ArticleIf you axis is skipping... (no replies)
If you axis is skipping without making noise, check to make sure the set screw on the belt pulley is tight. (That is assuming it's an axis with a belt pulley.) I have two set screws per pulley and one...
View ArticleNo Deacceleration? (no replies)
Hi, I have a strange behave at my CNC style Reprap. I use Repetier Host 0.90c and Firmware 0.83 an it works well. But I have to reduce the speed limits to very low values. Because of the CNC style...
View ArticleTemperature control issues (no replies)
Somewhat randomly, my hot end just cools off on its own sometimes during prints. I am printing from SD, but watching in pronterface and If I watch it, I can catch it and just command the hot end back...
View ArticleNoch'n Delta (no replies)
Habt ihr den schon gesehen? [www.thingiverse.com] Wersydingens
View ArticleBowden Extrusion w/ 0.25mm Nozzle (1 reply)
I'm in the process of getting my Rostock to begin its first print but I have been having issues with my extruder (you can read about it in my thread). This thread is about gathering information on...
View ArticleHEY T H E R E (no replies)
Hi - anybody out there ??? I'm Steve. I am wondering how many people are using 3d printers? Figure the reprap forum is as good as any for a poll. I live on North-side of Indy. I've been to the Club...
View ArticleNot Enough Power Being Supplied (1 reply)
I had only been printing with pla and no heated bed since I built my printer but recently decided to install the heated bed. The problem was when I tried to heat it during the print it could not heat...
View ArticleGetting Marlin going on a Brainwave board (no replies)
As a follow-on to my previous long-winded post on a Marlin overview (particularly as it applies to a Brainwave board), I did manage to get everything going to the point where I can drive motors....
View ArticleClik here to view.
Mendel90 verbindungs Probleme (no replies)
Hallo, ich versuchge gerade meinen Drucker zu verbinden habe über Adroino Melzi w ausgewählt und die Merlin Firmenware rüber geschupst und das hat auch geklapt upload erfolgreich, aber sobald ich ich...
View Articlemi termistor exploto (no replies)
el termistor honeywell que estoy usando exploto, alguien tiene alguna idea de porque lo hizo? muchas gracias.
View Articlethermistor issues (no replies)
my thermistor honeywell exploded, does anyone have idea why? sorry for my bad english
View ArticleSquaring and Tensioning woes (no replies)
Hi everybody! I've been working on my Tantillus build and have hit a snag when trying to square and tension the X/Y cables. After positioning the XY carriage in the front left corner, I pull the loose...
View Articleayuda - novato total intentando montar prusa i3 (no replies)
buenas soy jorge .. y bueno hace unas semanas me comenze a interesar por esto de la impresión en 3D... después de varios tipos de impresoras .. me gustaron la rocstock y la prusa i3 . Al final he...
View ArticleLosing Steps - Different firmwares (no replies)
First, I know that I'm probably losing steps. It's not a slipping belt, slipping pulley, motor current, drivers overheating, etc. I've tested pretty much everything I could and I still get disaligned...
View ArticleZ axis not moving during print (no replies)
Hi, I am currently using marlin firmware with ramps 1.4. I have tried manually move the stepper motors. It seems to work pretty well but, when i tried printing something the z axis doesnt moves :( Any...
View Articlewaves only in black ABS (1 reply)
So I noticed that anything I print in black that has any large flat areas and is printed solid has these waves. The waves start on the first layer and transfer to all other layers. If there is say 50%...
View ArticleExtruder motor stops turning midway through print (no replies)
I have a Makerfarm v2 Prusa (Printrboard, Marlin firmware, Pronterface) using Greg's extruder and a NEMA 17 motor. Every single time so far, the extruder has stopped moving in the middle of the print...
View ArticleRostock Troubleshooting (no replies)
Hey 3D friends, unfortunately I need help ones again. My Rostock is fully assembled Extruder and Bed are heating up quickly Temp sensors and endstops are running good But Rostock makes bullshit......
View ArticleClik here to view.
what do you revise me here? (8 replies)
I am trying to get my pursa mendel 2 to work properly .What problems do you see here and HOW can i fix problems please? I am new and i cannot understand whats wrong. I have measure the length of the...
View Article