Delta Pi - Directional Z skewing? (no replies)
[attachment 25917 bad_print.jpg] My first attempt to print a large object is showing this really strange effect. It would seem that depending which direction the print-head is travelling the Z axis...
View ArticleMaterial de Soporte en Impresion (1 reply)
tengo el siguiente problema, y por ahi los mas experimentados en impresion tienen mas idea.... Cuando trato de imprimir con material de soporte, termina siendo un dolor de cabeza, el sacarle el...
View ArticleHelp Please - One of Z axis Motor CANT CONTROL! (3 replies)
Hi I have Mendelmax 1.5 with Megatronics v2.0 running with Marlin firmware. Everything is fine except one of the z axis motor. When I run printrun to test homing, axises I see that one of the z axis...
View ArticleHow to mount extruder?! Prusa i3 (1 reply)
Hi Guys! I'm at the point where I can almost taste the completion of my prusa i3 but I've struck a problem! I was originally going to buy a qu bd extruder but due to the seemingly bipolar reviews on...
View ArticleStepper making noises but not moving very much (no replies)
Hey guys, I got this arduino mega/ramps/pololu combo [www.ebay.com] from china last week. Put everything together (as every single piece was separate) and tested. The result wasn't very pleasent. I...
View ArticleFried Stepper Driver? (2 replies)
Hi, I've been causing myself more problems here lately, but it started with my heatbed failing. So I tried to test the mosfet and accidentally touched the probe to a fuse instead of a bed terminal. I...
View ArticleCleaning glass so your parts stick (2 replies)
I'd like to share how I got PLA to stick to the glass on my heated bed. I was experimenting with different cleaners and nothing was working. I tried white vineger, mineral spirits, nail polish...
View ArticleRandom Endstop Hit Error (1 reply)
Alright Reprap experts, I need your help. I am a total newbie, so I apologize if I am missing something basic here. When beginning a build, I get a "Hit Endstop:Y" message on my LCD screen, and the...
View ArticlePLA Suppliers: South African trouble (1 reply)
Hi there everyone. I am currently running the printer about every second that I can to print the boxes I need and so on. I fear I am running low on PLA filament and I would like some advice on how to...
View Articleazteeg x3 with repetier host (no replies)
After updating to 95 e and then f (or d)heaters quit ...host shows them heating but after 5minutes or so the temps start dropping only a complete reboot will it go back to working then only for about...
View ArticleZ axis zeroing issues [resolved] (5 replies)
Hello I have been trying to set my Z axis manually and following the instructions found on the forums. I do not want to use the z probe as the measurements always keep varying to wildly due to the bad...
View ArticleGen6 mit heizbett? (no replies)
hallo leute.... :) ich hab hier mal ne frage.... weil ich mich persönlich nicht wirklich mit elektronik auskenn... und dafür 2 linke hände hab... :D also... ich hab so einen "billig" drucker.... der...
View ArticleProdám EASY 3D MAKER 0.5 (no replies)
Prodám 3D tiskárnu EASY 3D MAKER, nemám na ni moc čas a zbytečně doma stojí a dostal jsem chuť sestavit si vlastní. Má pevnou robustní kovovou konstrukci. Nedávno byla na servise, nějak se porouchalo...
View ArticleRADDS Board mit Bauteilen oder nur Bauteile Versandkostenfrei (no replies)
Hallo, RADDS-Board pur (nicht Versandkostenfrei) [youprintin3d.de] 14,99 € plus Versand RADDS-Board plus Bauteile (Versandkostenfrei) [youprintin3d.de] 41,99 € RADDS-Board plus Bauteile plus 6xDRV8825...
View ArticleNeed help with endstop setup (no replies)
Hi, I act a little bit like a fool when it comes to setting up the endstops... so hopefully anybody can tell, how the correct setup for my Prusa i2 would be like. I use mechanical endstops and...
View ArticleMakeraser Review (no replies)
I just finished a review of the Makeraser on my website if anyone is interested. For those of you who don't know what makeraser is. It is an acetone pen for smoothing prints, preping printbeds, and...
View ArticleClik here to view.
Assembled Prusa i3 from Makerfarm (no replies)
I bought this reprap a few weeks ago. After getting it working, I've had no complaints with the printer. Everything is calibrated well and it performs well also. This was a kit I bought from...
View ArticlePRUSA I3 Rework Calibration (11 replies)
Bonjour a tous, Je viens de finir une I3 achetée chez EmotionTech. Le montage ne s'est pas trop mal passé (malgré la qualité un peu bof des plastiques) , mais au niveau de la configuration, là je...
View ArticleHeat bed taking a long time (no replies)
I've been having trouble getting my heatbed up to the right temps. Initially the problem seemed related to running the printer through Pronterface. Once I started printing directly from an SD Card, it...
View ArticlePololu DRV8824 behavior vs 8825 -- what's going on here? (4 replies)
Hi all, I'm new to this forum, so if I'm posting in the wrong place my apologies, please point me in the right direction. I'm in the process of building a repstrap, and since getting everything put...
View Article