95e error message at startup (no replies)
Just installed version 95e on 2 system, both old and running clean installs of XP. One is fine. The other gives the following message: See the end of this message for details on invoking just-in-time...
View Articlevibrazione motori asse x y (2 replies)
Salve, non capisco come mai i motori asse x e y quando stampano fanno delle vibrazioni come se andassero a scatti, ho provato a cambiare parametri su ardoino ma non migliora niente ho anche abbassato...
View ArticlePrinting ABS using Elmers glue on the bed (1 reply)
I have previously been printing ABS on 6mm glass at 110 deg C covered with Kapton tape and a layer of ABS juice. It has been the most successful method I have found so far. But it is a load of hassle....
View ArticlePremier démarrage Prusa Air 2 (1 reply)
Bonjour, Je démarre tout juste dans la 3D. j'ai fini de monter une Prusa air 2 et dés la mise sous tension je m'aperçois que le moteur moteur Y ne se bloque pas comme les autres. J'ai essayé de...
View Articlerealizzazione Prusa i3 (c'è nessuno della provincia di Belluno?) (3 replies)
Cia a tutti , sono un nuovo iscritto del forum, e questo è il mio primo post. In primis… Complimenti a tutti. Forum super attivo e con utenti che …. beh a volte fate paura, in senso positivo, ma ho...
View Articlefan mount mod (no replies)
hey all, so had issues with feed clogging on my i2, took some time off and did research into methods of keeping temps regulated. really had issues with mounting to y mount so had to look into other...
View ArticlePrusa i3 with Dual Extrusion (no replies)
Hello Everyone, Someone is looking for a dual extrusion option. I have some unfinished Prusa i3 frames left, and I've seen a few of that style with dual extrusion. Does anyone have any suggestions,...
View ArticleNozzle valt uit J Head Nozzle holder (no replies)
Beste reprappers, Zaterdagavond laat zit ik nog lekker te rommelen met mijn printertje....printen, afstellen...te warm, te koud. Komt tijdens het printen mijn nozzle los van de J Head nozzle holder en...
View ArticleMagnetické senzory pro End-stop (no replies)
Naskytla se možnost vyrobit pár sad těchto čidýlek na dorazy.. Byl by o ně zájem? cenově hádám osazený DPS i s magnetkem a káblíkem cca 200,- ale všechno je ještě v řešení.. Ptám se jen předběžně...
View ArticleChoosing PLA Filament (no replies)
I'm new to the RepRap world, and am looking for good quality PLA filament. Quality of the resulting part is the most important factor, though price also plays a role. I don't care about appearances....
View ArticleLooking for good Repetier settings for Printrbot? (no replies)
Hi, I've been working with Printrbots for a while now, and overtime been developing these settings for the best Printrbot Simple print! I hope this helps some of you out :) [www.instructables.com]
View ArticleDirect Drive Lasercut Extruder :-) (2 replies)
Hliník 3 mm, řezáno laserem, příprava v CAD.. po řezání broušeno.
View ArticleRepetierHost (2 replies)
It may not be the best place for this question but I have found something strange with Repetier and Netfabb. I generate my STL in CAD (using Catia V5) and occasionnaly I rotate the parts using...
View Article3 Extruder problem (no replies)
Thank you for the wonderfull piece of software that you share with us. I am using Repetier-Firmware configuration tool for version 0.91 Rev 4 and the latest Repetier host software V0.95E on a delta...
View ArticleNewbie with a problem - can't get bed to heat up at all :( (21 replies)
Just finished building and all looking very hopeful on the commissioning front EXCEPT I can't get the bed to warm up at all :( If I send an M105 code in a monitor window I get: ok T:27.7 B:-39.7 I am...
View Articlecnc mach3 en 3d (no replies)
buenas soy nuevo con estas cosas haber si me podéis ayudar?tengo una copiadora manual y la quiero convertir en una cnc tengo unas medidas muy limitadas en espacio y necesito que tenga de z 200 mm sin...
View ArticleBreakthrough on getting getting duet to talk to laptop and read SD card (2...
I have seen a lot of posts about problems getting the duet to talk to laptops and thought I would share something I found that solved the problem for me. Although the laptop could see the duet, It...
View Articlemy first printer / MendelMax 1.5 or Prusa i3 (no replies)
Hi everyone, while thinking about buying a DIY 3D printer kit I searched the internet and read quite a lot about it on different blogs and forums. But still I can't figure out a couple of deciding...
View ArticleTantillus Case printed in one shot (3 replies)
Hello I just noticed that there is an stl for a full printed case [github.com] I am almost finished with my newest printer that will be able to print this with ease. My question is before I waste any...
View ArticleRostock or Prusa i3 (2 replies)
Hello all, I'm the proud owner of a (mostly) working Techzone Huxley, and I really want to use it to print parts for a superior printer. Trouble is, I can't really decide what would be better for my...
View Article