Hello to RepRap Users in Japan (no replies)
Hello all! First of all, thank you so much Victor to create this sub forum. Here is for all members in Japan. Please share news and info about RepRap and 3D printers in Japan. Any related topic would...
View ArticleWant to design and build custom printers in Indonesia? Or contribute in...
I'm new to 3-D scanning and printing, and so far have a setup that can scan full bodies and print to max size of 20 x 20 x 25 cm on our rep-rap based printer we purchased out of China. I'd like have...
View ArticleSlic3r generates gcode that retracts but doesn't advance :S (2 replies)
If I have retraction enabled, the filament is pulled back but then not advanced to the point it started at. If I disable retraction then the gcode is fine. Here is the start of the gcode and a small...
View ArticleServo driver heatsink? (3 replies)
Hi all, Just wonder if servo driver IC on the new duet board need heat sink ? servo current pre-set in firmware or in config file ?
View ArticleATX power supply unit (PSU) cuts out when all electronics are connected (2...
Hi everybody, After a lot of readying finally my first question on this forum. I have build my own reprap 3D printer based on the delta-pi with some modifications. A couple of days ago I finished the...
View ArticleMarlin/RAMPS heater bed PID vs. bangbang settings (1 reply)
I have a reoccurring problem with my ramps board overheating when driving a heater bed. I have a 12V 30A power supply and the resistance across my heater bed and leads is about 4.8 ohms. I buy the...
View ArticleY axis skipping (2 replies)
Ok. I have been running my prusa i2 for a while now and have an odd problem. The y axis appears to skip on longer prints, but not all of them. I am using white lithium grease on the rods, and it even...
View Article[Canada] mUVe 1 UV Photopolymer 3D Printer for sale (no replies)
Hello all, I am selling my mUVe 1 3D printer. I assembled this Ultimate kit and made some significant modifications to it over the last few months but have not had time to play with it. I am a tool...
View ArticleClik here to view.
Disclauncher from Tribes Ascend PC game (1 reply)
So cool, have always wanted to be able to make objects from the games I play. Pretty easy if you can extract the files from the game and do a little work to them to make them print ready. Was printed...
View Articlecode erreur de com serie : system IO ports ... (no replies)
bonjour à tous, Je viens de terminer le montage de ma reprap huxley et je passe donc à la programmation de celle-ci, mais, problème, voici le message qui s'affiche sur mon ordi quand je la met sous...
View ArticleNach etwa 2 Stunden Druck kommt Versatz in X-Richtung:S (5 replies)
Hallo zusammen und frohe Weihnachten, grundsätzlich funktioniert mein Mendelmax problemlos. Leider habe ich nach gut 2 Stunden Druckzeit (das variiert und kann auch später kommen) ständig einen...
View ArticleConectando un lcd - de gadgets3d (no replies)
Hola una feliz navidad y un prospero ano nuevo a todos. Regresando a la empresora. Alguien sabe como programar un lcd de gadget3d . Estoy usando proterface y slic3r. Esperando por ayuda gracias y saludos
View ArticleImproving my print quality (no replies)
Hi! I've recently built a Prusa Mendel i2 and over the last few days have gotten it to print rather reliably. Now I'm trying to improve my print quality and was wondering if anyone would mind giving...
View ArticleInfill 3D SunBurn hot end? (no replies)
Hello all, I just checked with the IRC channel to see if anyone has used this hot end [cgi.ebay.com] with no luck, I am wondering if anyone has experience with it? I contacted the seller and he has...
View ArticleRepetier Host: Marlin oder Repetier Firmware? (4 replies)
Hi, könnt ihr mir mal aus eurer Erfahrung schildern, welche Firmware "besser" zur Repetier-Host Software passt. - Ich weiss nur, dass mit Marlin das große LCD-Display funktioniert, mit Repetier soll...
View ArticlePrintrun installation impossible sous debian (1 reply)
Salut tout le monde Je me présente, je suis nouveau sur le forum ( et je fais beaucoup de fautes d'orthographe je sais mais c'est parce que je suis encore un étudiant (:D. (mauvaise excuse)) Je suis...
View ArticleSystème permettant de retenir la poussière (no replies)
Salut tout le monde J'aurai voulu connaitre vos truc et astuce pour empêcher la poussière d'atteindre la buse. Merci bonne journée
View ArticleWas haltet ihr vom Printbot simple? (3 replies)
Hi 3D Druck Experten, ich suche einen 3D Drucker für einefache aber funktionale bastel Teile für dieverse Projekte. Die meistern 3D Drucker sind mir ehrlich gesagt noch zu teuer aber ich habe den...
View ArticleClik here to view.
Spostamento layer (2 replies)
Salve a tutti, sono nuovo del forum , ho costruito da poco una prusa I2, come elettronica uso una ramps 1.4, come firmware uso sprinter, slicer per generare i gcode e printrun per il collegamento con...
View ArticleOrmerod MXL Belt Tooth count? (1 reply)
Hello all! I'm Mitch from the Philippines. Would anyone happen to know, the specs of the MXL belt used on the Ormerod? I know the belt is: black rubber MXL belt, 1/4" (6.35mm) wide, 1.7m long, but the...
View Article