2 Extruders, une imprimante (no replies)
Bonjour à tous, Je voudrais savoir comment se fait le passage d'un extruder à l'autre lors d'une impression!! Est-ce que ça se fait via une fonction sur le GCode, ou bien un réglage au niveau du...
View Article[SALE] Complete KIT of Electronics RAMPS 1.4 in eBay (no replies)
Hello friends. I bring a new electronic kit. This time cheaper >:D< I realize shipping throughout the world. Here's the link to the ebay ad: [www.ebay.com] What does our kit include? - 1x RAMPS...
View ArticleBeginner: Setting temperatures (no replies)
Hi, How do I set the hot end / bed temperature the right way? I noticed with the PLA I'm using that setting the temperature to 200°C yeilds better results than at 220°C. Now I've been changing the...
View ArticleComeçando em São Paulo / Starting in São Paulo (no replies)
Bom dia, Estou interessado em montar alguma variação da reprap em minha casa e gostaria de saber se alguém está vendendo partes em São Paulo. Vocês acham mais vantagem comprar nos EUA, em alguma...
View ArticleFilament feed issues (4 replies)
I've had two long prints fail on me because the filament gets stuck and the extruder just grinds it down. Aside from losing 650mm of filament, I also can't leave the printer for any extended length of...
View ArticleY slip but then again not (1 reply)
Hi All I dont understand this one. My printer seems to slip in Y while printing long lengths however when I tested it with the .4 thin wall stretched by 2 in the Y it was fine. see attached...
View ArticleGreg's Wade Extruder Printed Parts For Prusa, MendelMax, RepRap (no replies)
Greg's Wade Extruder Printed Parts For Prusa, MendelMax, RepRap PLA printed parts. Get yours here! Thanks! [www.etsy.com]
View ArticleWellen an der Oberfläche... (7 replies)
...also die gleichmäßig verteilten vertikalen Wellen oder Linien, die man auf dem Bild sehen kann. Woher kommen die und wie krieg' ich sie weg? Ich hab' bisher immer gedacht, es liegt am Zahnriemen,...
View Articleodd Y axis moves (no replies)
Hi I'm not sure if i have raised the below link in the right place as i dont think it is software related Can you have a look and see what you think [forums.reprap.org] Cheers Mike
View ArticleThin ‘solid’ parts ending up hollow. (no replies)
I am trying to print some solid ‘U’ shaped brackets with 20mm (inside) sides to clip on to some 20mm box profile. The clip is currently 2.5mm thick. The first one printed fine but I slightly increased...
View ArticleClik here to view.
Meßschieber - Output Connector (4 replies)
Welcher Stecker passt in den "output connector" - (Lt. Datenblatt) - des China Meßschiebers? Danke Achim
View ArticleEffects of slop between hobbed bolt and bearing (6 replies)
Why are we using m8x22 ball bearings for the extruders and then putting a 8mm "hobbed bolt" through it that is smaller than 8mm? If you could buy bolts that actualy measure 8mm on the OD this would...
View Articlecomponents for jhead MKV (2 replies)
Hi, my jhead jammed so I'm planning to buy another one. The thing is I want to assemble my own, sort of as a learning experience and because i want to recycle some of the components from the jammed...
View ArticleMoteur axe Y bloqué (5 replies)
Bonjour à tous ! Voila, ça fait maintenant quelques jours que je suis bloqué sur un truc. Le moteur axe Y refuse d'obéir correctement (voir pas du tout) quand je lui demande de tourner. j'ai tout...
View ArticleNo abre el skeinforge.... (1 reply)
Alguien me puede decir como m....:X:X, abrir el skeinforge desde el pronterface. Les cuento un poco: Descargué el printrun desde acá github.com/kliment/Printrun Y bajé el skeinforge de la pagina de...
View ArticleSlicer stopping extruder during bridging (no replies)
during the fabrication of a bridge the last few strings will not be extruded. the printer keeps moving to create the bridge, but the extruder does not. i have my brige flow ratio set to 0.96 and...
View ArticleWhat is required for ramps? (3 replies)
Hey Guys Building my first reprap, trying to make it as cheap as possible :) Is $100 a good deal for: - 5 Pololu Stepper drivers - Ramps 1.4 shield - Arduino mega 2560 - endstop + cables...
View ArticleLayer Shifting (no replies)
Good Afternoon! I built a Mendel90 from a kit from Nophead, and it is using Melzi electronics. I am using Slic3r to generate gcode files and using Pronterface to operate my printer. What I am noticing...
View ArticleSkeinforge initial travel speed very slow (1 reply)
My irritation is that when Skeinforge slices an STL it sets the initial travel speed moving from home to the start of the skirt to F60.0 This is dramatically slower than the rest of the print - layer...
View ArticleSlic3r g code settings (1 reply)
Hardware InDimension3 Glacier Summit dual head printer Software Repetier-Host Mac 0.56 with Skeinforge 50 and Slic3r 0.9.9 Firmware RepRap Marlin/Splinter We have a 1mm extruder head. We want to do...
View Article