Calibrazione, link, tutorial e suggerimenti (Aiuto) (no replies)
Salve a tutti, Ho un problema nella preparazione per la stampa in PLA, ma teoricamente posso calibrare la mia Prusa nel frattempo. Ho letto molto, incluso il reprap calculator, ma sono proprio un...
View ArticleNew extruder design on indiegogo (5 replies)
I saw this extruder and I thought I should share it with you guys. http://www.indiegogo.com/projects/the-kraken-the-first-dual-independent-pinch-wheel-extruder-for-3d-printers It's called the Kraken...
View ArticleRepraper New in London (no replies)
Hello everyone. I am new in London, and from some months I am try to build a Prusa i3.... I am confident to finish my printer soon. (calibration and software solution)..well i have a couple of...
View ArticleIl perchè dell'estrusore a vite (5 replies)
Ho inserito un piccolo filmato dove si capisce molto bene quali sono i limiti di "velocità" che "normalmente" si utilizzano nella stampa 3D. In questo caso parliamo di limiti "minimali" con stampanti...
View ArticleClik here to view.
Fixed torn USB receptacle (no replies)
Hey all, First time poster. I have a RepRap Mendel mono. I have enjoyed learning how to create good prints. I recently had a problem, and I wanted to share the fix with anyone else that might have the...
View ArticlePrinter Disconnects And Not Reconnect During Printing Issue (no replies)
I have been having an issue. It has cropped up in the last two days. The part will start printing, print for ~45 minutes, then just cut out. The printer head stops. Printer Interface says that the...
View ArticleMal was einfaches... Endstops einstellen (2 replies)
Hallo Leute, sorry, wenn ich jetzt eine dumme Frage stelle und die Antwort hier im Forum sicherlich schon zu finden ist. Aber ich bin des "googlens" und "Forumdurchsuchens" überdrüssig. Zu viel Zeit...
View ArticleDoes anyone grease or oil threaded rods? (1 reply)
Recently one of the Z-axis threaded rods on my Prusa i3 started making noises. I added a small amount of silicon grease (the type used for garage door screw mechanisms) to the part of the rod which...
View ArticleSi sono tolte le "viti" per regolare velocita motori Ramps 1.4 (3 replies)
Salve... Sarò stanco, ma risolvo un problema e se ne creano 2:( Stavo regolando la velocita del motore dell asse X...e le "viti" (che non sono viti) sono letteralmente cadute:( Ho rotto la Ramps ????...
View ArticleForging (no replies)
I'm not sure if this is the right place to post this, but since this is about 3d printing in metal, I thought I might put it here. I was wondering if anyone has ever come up with a method of producing...
View ArticleClik here to view.
Hallow inside (4 replies)
I just printed a small gear part for Greg's Wade extruder. The overall print quality is alright, however I can see there's some void between the center hole and the gear teeth. I don't think it's...
View ArticleOnly 7 steps per mm extrusion? (2 replies)
I have an older reprappro mendel that I just finished putting together. I updated the firmware on it to the latest marlin. I also have the latest pronterface. When I tested the extrusion, it extrudes...
View ArticleHotend temp varies (no replies)
I have a prusa mendel i2 with RAMPS electronics. I also have the budaschnozzle 2.0 hotend. When I set my hotend temp to 195 it goes up to 210 then down to 188. It continues to go up to 210 then down...
View ArticleFilament force? (1 reply)
Can anyone give me a ballpark guesstimation of the force level it takes to push a 1.75mm filament through a .4mm hot end nozzle at a typical temp and extrusion velocity? Thanks in advance.
View ArticleCAPIRE SE NEMA 17 HA L'ALBERO CON LA FRESATA (2 replies)
Sto per comprare due Nema17 per la stampante che sto costruendo. Ho trovato questo: [www.robot-italy.com] Per non fare scivolare la puleggia ci vorrebbe la fresatina sull'albero, come faccio ad essere...
View ArticleEsto se supone que es así??? (2 replies)
Hola a todos!!, esto se supone que es asi???? les cuento que tengo una impresora kikai y me sucede que a veces se me salen las tuercas de las guias de fibrofacil que la presionan. Deberia ser asi...
View ArticlePrinting configuration (no replies)
Hello, I'm trying to print X carriage and X end for my Prusa i3 printer. I bought a kit from MakerFarm and it uses laser cut wood instead of printed parts, except for the extruder. I did not like the...
View ArticleFrage zu Sanguinololu (5 replies)
Hallo, Ich habe ein Frage zu meinem Sanguinololu Board. Ich habe das Board mit den Screw Terminals, was bedeutet ich brauche ein externes Netzgerät oder ein Labornetzgerät. Mich würde jetzt...
View ArticleFilament klar (4 replies)
Hallo, Ich hab schon so viele Farben von Filaments gesehen, aber ich bin verzweifelt auf der Suche nach einem durchsichtigen (klaren) Filament in der Dicke 1,75. Gibt es so etwas, wenn ja, wo bekommt...
View ArticleAnyone using Repsnapper with Mendel90? (no replies)
Hi, I am using Fedora 19 as my host platform and, of the many 3D printing applications packaged, Repsnapper looks interesting. Is anyone using this software with the Mendel90 and, if so, what are your...
View Article