Up for sale is a Rostock 3d delta printer kit that is nearly complete with a ton of extra parts, so technically you could build a different type Reprap you just need the printed parts. Only things needed to complete the printer are 3 endstop switches, 3 more powerful Nema17 motors if you chose, and misc hardware/vitamins, longer GT2 belts if you want full height or braided line instead.
Parts:
Rostock plastic parts in PLA
1/2" birch plywood top and bottom plates
6 x carbon fiber rods with Traxxas ball ends installed - 250mm eye to eye
6 x 3ft 8mm tight tolerance 12L14 carbon steel drill rod from McMaster $4/ft! better than O1 drill rod!!
1 x MK1 PCB heatbed
1 x Complete Wades extruder
1 x J-head hotend with 100k thermister install and all wired up!!
1 x 12V computer Power supply
1 x complete Ramps 1.4 with Ardu board, 5 drivers, 1 SD card reader
1 x complete set of wires
4 x Nema 17 stepper motors - NEW
1 x airtrapper extruder parts
1 x toothed pinion for airtrapper extruder
1 x Arcol hyena V2.0 hobbed bar
1 x 40mm 12V fan
1 x Complete Trinity labs Microextruder
3 foot of Teflon tubing for Bowden setup
18 x LMU8 linear bearings
6 x printed PLA LMU8 bushings
5 x regular 8mm bearings
10 x smaller 5mm ID bearing
4 x 10mm bronze bushings
2 x aluminum T2.5 pulleys
1 x T2.5 belt
3 x GT2 pulleys
3 x GT2 belts from Ultimachine
10 x 8mm flanged bearings
3 x new 100k thermisters
3 x PLA printed pulleys for Braided Line (Spectra) - RichRap's design!!
Misc. 3mm bolts, nuts, washers
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
Asking $300 shipped to cont. 48 states, if you want it international I'll have to give you a quote. I'm in Atlanta, GA if anyone local wants it. Email or PM me with questions!
Payment accepted via Paypal only. I'm an honest hobby Reprapper who needs the money more than another printer at this point. My Ebay ID is Bud_45lcacp and brushlessmuggy for references. Parts will ship ASAP after payment via FedEx ground.
I will also throw in 1Kg of Ultimachine Sliver ABS or Purple PLA as a Bonus, just tell me which one you want!!
Parts:
Rostock plastic parts in PLA
1/2" birch plywood top and bottom plates
6 x carbon fiber rods with Traxxas ball ends installed - 250mm eye to eye
6 x 3ft 8mm tight tolerance 12L14 carbon steel drill rod from McMaster $4/ft! better than O1 drill rod!!
1 x MK1 PCB heatbed
1 x Complete Wades extruder
1 x J-head hotend with 100k thermister install and all wired up!!
1 x 12V computer Power supply
1 x complete Ramps 1.4 with Ardu board, 5 drivers, 1 SD card reader
1 x complete set of wires
4 x Nema 17 stepper motors - NEW
1 x airtrapper extruder parts
1 x toothed pinion for airtrapper extruder
1 x Arcol hyena V2.0 hobbed bar
1 x 40mm 12V fan
1 x Complete Trinity labs Microextruder
3 foot of Teflon tubing for Bowden setup
18 x LMU8 linear bearings
6 x printed PLA LMU8 bushings
5 x regular 8mm bearings
10 x smaller 5mm ID bearing
4 x 10mm bronze bushings
2 x aluminum T2.5 pulleys
1 x T2.5 belt
3 x GT2 pulleys
3 x GT2 belts from Ultimachine
10 x 8mm flanged bearings
3 x new 100k thermisters
3 x PLA printed pulleys for Braided Line (Spectra) - RichRap's design!!
Misc. 3mm bolts, nuts, washers
Asking $300 shipped to cont. 48 states, if you want it international I'll have to give you a quote. I'm in Atlanta, GA if anyone local wants it. Email or PM me with questions!
Payment accepted via Paypal only. I'm an honest hobby Reprapper who needs the money more than another printer at this point. My Ebay ID is Bud_45lcacp and brushlessmuggy for references. Parts will ship ASAP after payment via FedEx ground.
I will also throw in 1Kg of Ultimachine Sliver ABS or Purple PLA as a Bonus, just tell me which one you want!!