Hi all,
new to RepRap, live near Hamilton, and looking to build a Box Frame Style Prusa I3.
I've been going Prusa's GitHub trying to get as much of the BOM from there for what I guess you would call the original build.
however it seems to be missing some information, is there anyone here more fammiliar with the Prusa I3 that might be able to fill in the blanks?
from the Wiki I see no one has a firm grasp on the exact amount of fastners required for this.
I've even tried translating Prusa's Norwegian BOM but it still makes no sense.
form the Vanilla branch I did find an incomplete BOM for each of the main parts, however it is missing the Z axis or Frame parts, any input very much appreciated
==The gregstruder==
Plastic parts needed:
-Extruder body
-Extruder idler
-Extruder large gear
-Extruder small gear
Other parts needed:
-1 NEMA17 motor
-1 hotend
-1 M3x8 grub screw
-6 M3 nuts-
3 M3x40 bolts
-1 M8x20 grub screw
-1 M8 hobbed bolt
-4 M8 washers
-2 M8 nuts
-3 608 skateboard bearings
-3 M3x10 bolts
(optional) 2 short, stiff springs or silicone pads
===Assemble the X axis (P2)===
Plastic parts needed:
-x axis motor end
-x axis idler end
-x carriage
Other parts needed:
-1 NEMA17 stepper motor
-1 T2.5 belt
-3 M3x10 bolt
-1 belt drive pulley
-1 M3x8 grub screw
-1 ??? bolt
-1 ??? bearing
-7 linear bearings
-7 M3x25 bolt with nut and washers
-2 smooth rods
===Assemble the Y axis(P2)===
Plastic parts needed:
-y axis motor holder
-4 y corners
-y axis idler
-y belt clamp
-3 y bearing holders
Other parts needed:
-1 23x23cm 12mm plate (9"x9" 1/2" thick for people in inchy countries) (may be thinner)
-1 heated bed PCB, with wires attached
-1 glass plate covered with Kapton or PET tape
-1 NEMA17 stepper motor
-1 T2.5 belt
-2 M3x10 bolt
-1 belt drive pulley
-1 M3x8 grub screw
-1 ??? bolt
-1 ??? bearing
-3 linear bearings
-3 M3x25 bolt with nut and washers
-2 405mm smooth rods
-22 M8 nuts (substitute 5/16" for M8 in inchland)
-22 M8 washers
-12 M10 nuts (?? in inchland)
-12 M10 washers
-4 140mm M8 (5/16") threaded rod (longer is ok)
-2 430mm M10 (??/16") threaded rod (longer is ok)
-9 3.5x12mm wood screws (or shorter if your plate is thinner)
new to RepRap, live near Hamilton, and looking to build a Box Frame Style Prusa I3.
I've been going Prusa's GitHub trying to get as much of the BOM from there for what I guess you would call the original build.
however it seems to be missing some information, is there anyone here more fammiliar with the Prusa I3 that might be able to fill in the blanks?
from the Wiki I see no one has a firm grasp on the exact amount of fastners required for this.
I've even tried translating Prusa's Norwegian BOM but it still makes no sense.
form the Vanilla branch I did find an incomplete BOM for each of the main parts, however it is missing the Z axis or Frame parts, any input very much appreciated
==The gregstruder==
Plastic parts needed:
-Extruder body
-Extruder idler
-Extruder large gear
-Extruder small gear
Other parts needed:
-1 NEMA17 motor
-1 hotend
-1 M3x8 grub screw
-6 M3 nuts-
3 M3x40 bolts
-1 M8x20 grub screw
-1 M8 hobbed bolt
-4 M8 washers
-2 M8 nuts
-3 608 skateboard bearings
-3 M3x10 bolts
(optional) 2 short, stiff springs or silicone pads
===Assemble the X axis (P2)===
Plastic parts needed:
-x axis motor end
-x axis idler end
-x carriage
Other parts needed:
-1 NEMA17 stepper motor
-1 T2.5 belt
-3 M3x10 bolt
-1 belt drive pulley
-1 M3x8 grub screw
-1 ??? bolt
-1 ??? bearing
-7 linear bearings
-7 M3x25 bolt with nut and washers
-2 smooth rods
===Assemble the Y axis(P2)===
Plastic parts needed:
-y axis motor holder
-4 y corners
-y axis idler
-y belt clamp
-3 y bearing holders
Other parts needed:
-1 23x23cm 12mm plate (9"x9" 1/2" thick for people in inchy countries) (may be thinner)
-1 heated bed PCB, with wires attached
-1 glass plate covered with Kapton or PET tape
-1 NEMA17 stepper motor
-1 T2.5 belt
-2 M3x10 bolt
-1 belt drive pulley
-1 M3x8 grub screw
-1 ??? bolt
-1 ??? bearing
-3 linear bearings
-3 M3x25 bolt with nut and washers
-2 405mm smooth rods
-22 M8 nuts (substitute 5/16" for M8 in inchland)
-22 M8 washers
-12 M10 nuts (?? in inchland)
-12 M10 washers
-4 140mm M8 (5/16") threaded rod (longer is ok)
-2 430mm M10 (??/16") threaded rod (longer is ok)
-9 3.5x12mm wood screws (or shorter if your plate is thinner)