Questions about print seams... (no replies)
In Slice3r there are 3 options for seams Random, Nearest and Aligned. 1- Nearest method, nearest to what? 2- Aligned, some of the seams are aligned but not all of them. In some of my prints the seams...
View ArticleX axis clatters at the first layers (no replies)
Hi! I use the following hardware: Anet AM8 MKS Gen 1.4 board TMC2130 drivers for X, Y and E (X and Y at 700mA RMS, E at 650mA RMS) At the moment I am using Marlin bugfix-1.1.x (b0f148f, 2018-01-25)...
View ArticleUnderextrusion oder Conturwidth ? (no replies)
Moin Moin.. Bei meinem Druck sind die Flächen nicht ganz gefüllt. Jedoch nur bei großen Flächen. Habe schon etwas mim Multiplikator gespielt, hat aber nicht viel gebracht. Meine Konturweite steht auf...
View Article"Plane" MK3 Heizbetten (1 reply)
Moin, gibt es irgendwo wirklich plane MK3 Heizbetten? 2 bestellt = 2 krumm ... Würde gerne wie toolson nur eine MK3+Pertinax verwenden um Gewicht zu sparen. Und 1mm Beulen kann man schlecht schleifen..
View ArticleFragen zur Slic3r Einstellung (no replies)
Hallo Spezialisten, ich drucke schon eine längere Zeit mit Skeinforge. Nun wollte ich mal sehen, ob es andere (bessere) Slicer gibt. Nun habe ich mal versucht SLIC3R zu kalibrieren. Geschwindigkeiten...
View ArticleThermal runaway analysis (no replies)
hello ! I'm currently having issues with thermal runaway protection, but i can't see big temperature differences in the graph on octoprint. Moreover, the error message doesn't specify which sensor is...
View ArticleErfahungen mit PLA von "Your Droid"? (no replies)
Hi, mein 3D Drucker kam heute, und siehe da, der Distributor für das - auf AliExpress bestellte Kit - ist roboter-bausatz.de und sitzt ebenfalls in Saarbrücken. Das ist insofern praktisch, als das die...
View ArticleChosing cheap a laser diode module (1 reply)
Hello everyone! I'm looking at laser diodes for engraving wood/cutting vinyl sheets. i'm aimed at 445/450 nm laser diodes because it is what i can source for relatively cheap, and we've determined in...
View ArticleProblem with my Prussia reprap i3 printer (no replies)
My printer makes a squeezing sound on the motors and only x axis moves and the motor is extremely hot. I used the Prussia Mendel_i3 marlin firmware early "Marlin firmware used for Prusa i3 Hephestos -...
View Articleleft probe bed position (no replies)
hi, my firmware was working fine until I just changed the bedsize from 220 to 210 for X and Y // The size of the print bed #define X_BED_SIZE 210 #define Y_BED_SIZE 210 now when I verify my firmware I...
View ArticleErrore di avvio di Cura 3.1 e 3.2 - max() arg is an empty sequence (no replies)
Salute e buone stampe. Riporto la mia esperienza nel risolvere un errore che crea non pochi problemi a chi installa le ultime versioni di Cura 3.1 e 3.2(BETA al momento di questa stesura) in ambiente...
View Article[SUCHE] Silikonheizmatte rund für ca 300mm Bett DELTA 230V (5 replies)
Hallo! Wie schon der Threadtitel verrät, bin ich auf der Suche nach einer Silikonheizmatte mit den groben Eckdaten: - 230V - 500W oder mehr - passend für ein ca 300mm rundes Bett für einen Delta. Ich...
View ArticleBed homing ? (no replies)
Hi Guys When the printer finishes it homes to the rear but i want it to go to the front so I can get the print off. Is there a way to make this happen in Cura. Thanks Adrian
View ArticleBiokompatibles, flexibles, transparantes STL Harz, (no replies)
Hallo Leute, für eines meiner Projekte bin ich auf der Suche nach einem bestimmten Harz für einen STL-Drucker. Leider habe ich bisher kein geeignetes gefunden. Gesucht ist ein Harz, Polymer o.ä, dass...
View ArticleFreeCad - Anleitung / Handbuch (2 replies)
Hallo, ich möchte FreeCad als Konstruktionssoftware verwenden. Da ich mich aber noch einarbeiten muß, bin ich auf der Suche nach einer Anleitung, möglichst in deutsch und zum ausdrucken oder als Buch....
View ArticleProblem with my printer (no replies)
The printer accepts the job and seems to start printing but some weard sound came also it heats up and the printer stops.pls help me Admin edit : Separated from unrelated topic, changed title...
View ArticleDelta Segments per Second (1 reply)
So I've been experimenting and trying to build my own delta for a few months now. And I needed some help with Marlin. I've reduced the Delta Segments per Second to 120 from the default 200, and it...
View ArticleMaker Select Melzi to Ramps 1.4 problem (no replies)
I just finished installing the Ramps board with the graphic lcd. Everything seems to work. When I select Home, the printer homes fine and I do a manual bed level. When I select print, the printer will...
View ArticleClik here to view.
HyperCube OverKill Build Log (no replies)
I can't believe it's been 6 months since I started the What's Wrong With This Picture thread but I guess life just got in the way. I haven't been idle though. In fact, I have (well had) a working...
View ArticleClik here to view.
Beacon 3D Printer (no replies)
urrRqaK.jpg hnxw16v.jpg Here's a quick shot of my workbench with completed printer. It's been a journey through three massive iterations over the course of two years but this one works like a charm....
View Article
![ONEW – KAKERA -Unmei no Piece- – EP [iTunes Plus M4A]](http://is1-ssl.mzstatic.com/image/thumb/Music221/v4/d0/fb/86/d0fb86a5-ba60-4bea-41fb-7f54c125f518/VEATP-45908.jpg/296x296bb.webp)
